Boot from specific partition using sd card - RCAR M06 KF Board

Hello everyone.

I hope everyone is doing well; I have one scenario for updating the device firmware.'


I have three partitions:
NO. 1 PARTITION - Boot folder (contains image and r8a7795-h3ulcb-4x2g-kf.dtb)

PART 2: Rootfs

PARTITION 3 - Empty partition - This is where the new rootfs will be unzipped/untarred.

During boot, I want to check partition 3 to read explicitly for rootfs, and if none is found, I want to check partition 2 for rootfs.

I've set the following u-boot parameters:

bootargs_emmc2='rw root=/dev/mmcblk1p2 rootdelay=5'
bootargs_emmc3='rw root=/dev/mmcblk1p3 rootdelay=5'
setenv bootargs "${bootargs_emmc2}; ${bootargs_emmc3}"
setenv bootcmd "ext2load mmc 0:1 0x48080000 /boot/Image; ext2load mmc 0:1 0x48000000 /boot/r8a7795-h3ulcb-4x2g-kf.dtb; booti 0x48080000 - 0x48000000"
saveenv

I followed the instructions at elinux.org/.../.
I'm getting the following error: devtmpfs: mounting error -2 (may be uboot not able to find rootfs but it is not fallback to read partition 2).

When I explicitly set bootargs to emmc2, the board boots up normally.

My question is whether there is a way to force uboot to read rootfs from part#3 if part#3 is not present, and to read rootfs from part#2 if part#3 is not present.

Any help will be appreciated Slight smile

Parents
  • Hi,

    I tried to reproduce it.

    The kernel booted without any problems.

    Please check the attached file for the boot log and how to reproduce it.

    If the reproduction method is wrong, please point out what is wrong.

    bootlog.txt
    Environments:
     H3 v3 Starter kit(RTP0RC77951SKBX010SA03) + Kingfisher
     Yocto BSP v5.5.0
    
     SD partition:
      0 : Image and r8a77951-ulcb-kf.dtb
      1 : rootfs
      2 : empty
    
     U-boot parameters:
    => setenv bootargs_emmc2 'rw root=/dev/mmcblk1p2 rootdelay=5'
    => setenv bootargs_emmc3 'rw root=/dev/mmcblk1p3 rootdelay=5'
    => setenv bootargs "${bootargs_emmc3};${bootargs_emmc2}"
    => ext4load mmc 0:1 0x48080000 /Image;ext4load mmc 0:1 0x48000000 /r8a77951-ulcb-kf.dtb;booti 0x48080000 - 0x48000000
    
    
    ---- boot log ---
    NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.3.0.2
    NOTICE:  BL2: PRR is R-Car H3 Ver.3.0
    NOTICE:  BL2: Board is Starter Kit Premier Rev.2.1
    NOTICE:  BL2: Boot device is HyperFlash(80MHz)
    NOTICE:  BL2: LCM state is CM
    NOTICE:  AVS setting succeeded. DVFS_SetVID=0x53
    NOTICE:  BL2: DDR3200(rev.0.41)
    NOTICE:  BL2: [COLD_BOOT]
    NOTICE:  BL2: DRAM Split is 4ch(DDR f)
    NOTICE:  BL2: QoS is default setting(rev.0.11)
    NOTICE:  BL2: DRAM refresh interval 1.95 usec
    NOTICE:  BL2: Periodic Write DQ Training
    NOTICE:  BL2: CH0: 400000000 - 47fffffff, 2 GiB
    NOTICE:  BL2: CH1: 500000000 - 57fffffff, 2 GiB
    NOTICE:  BL2: CH2: 600000000 - 67fffffff, 2 GiB
    NOTICE:  BL2: CH3: 700000000 - 77fffffff, 2 GiB
    NOTICE:  BL2: Lossy Decomp areas
    NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
    NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
    NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
    NOTICE:  BL2: FDT at 0xe6326f70
    NOTICE:  BL2: v2.5(release):ca03ad6-dirty
    NOTICE:  BL2: Built : 05:49:00, Sep 24 2021
    NOTICE:  BL2: Normal boot
    NOTICE:  BL2: dst=0xe6326800 src=0x8180000 len=512(0x200)
    NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
    NOTICE:  rcar_file_len: len: 0x0003e000
    NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=253952(0x3e000)
    NOTICE:  rcar_file_len: len: 0x00200000
    NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=2097152(0x200000)
    NOTICE:  rcar_file_len: len: 0x00100000
    NOTICE:  BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)
    NOTICE:  BL2: Booting BL31
    
    
    U-Boot 2020.10 (Sep 24 2021 - 05:49:07 +0000)
    
    CPU: Renesas Electronics R8A7795 rev 3.0
    Model: Renesas H3ULCB board based on r8a77950
    DRAM:  7.9 GiB
    RAM Configuration:
    Bank #0: 0x048000000 - 0x0bfffffff, 1.9 GiB
    Bank #1: 0x500000000 - 0x57fffffff, 2 GiB
    Bank #2: 0x600000000 - 0x67fffffff, 2 GiB
    Bank #3: 0x700000000 - 0x77fffffff, 2 GiB
    
    Flash: 64 MiB
    MMC:   sd@ee100000: 0, sd@ee140000: 1
    Loading Environment from MMC... OK
    In:    serial@e6e88000
    Out:   serial@e6e88000
    Err:   serial@e6e88000
    Net:   eth0: ethernet@e6800000
    Hit any key to stop autoboot:  0
    => ext4ls mmc 0:1 /
    <DIR>       4096 .
    <DIR>       4096 ..
    <DIR>      16384 lost+found
            24240640 Image
              125474 r8a77951-ulcb-kf.dtb
    => ext4ls mmc 0:2 /
    <DIR>       4096 .
    <DIR>       4096 ..
    <DIR>      16384 lost+found
    <DIR>       4096 bin
    <DIR>       4096 boot
    <DIR>       4096 dev
    <DIR>       4096 etc
    <DIR>       4096 home
    <DIR>       4096 lib
    <DIR>       4096 media
    <DIR>       4096 mnt
    <DIR>       4096 proc
    <DIR>       4096 run
    <DIR>       4096 sbin
    <DIR>       4096 sys
    <DIR>       4096 tmp
    <DIR>       4096 usr
    <DIR>       4096 var
    => ext4ls mmc 0:3 /
    <DIR>       4096 .
    <DIR>       4096 ..
    <DIR>      16384 lost+found
    => setenv bootargs_emmc2 'rw root=/dev/mmcblk1p2 rootdelay=5'
    => setenv bootargs_emmc3 'rw root=/dev/mmcblk1p3 rootdelay=5'
    => setenv bootargs "${bootargs_emmc3};${bootargs_emmc2}"
    => printenv
    baudrate=115200
    bootargs=rw root=/dev/mmcblk1p3 rootdelay=5;rw root=/dev/mmcblk1p2 rootdelay=5
    bootargs_emmc2=rw root=/dev/mmcblk1p2 rootdelay=5
    bootargs_emmc3=rw root=/dev/mmcblk1p3 rootdelay=5
    bootcmd=tftp 0x48080000 Image; tftp 0x48000000 Image-r8a77950-ulcb.dtb; booti 0x48080000 - 0x48000000
    bootdelay=2
    bootm_size=0x10000000
    ethaddr=2e:09:0a:06:d2:36
    fdtcontroladdr=bbeed350
    loadaddr=0x58000000
    platform=r8a7795
    stderr=serial@e6e88000
    stdin=serial@e6e88000
    stdout=serial@e6e88000
    usb_pgood_delay=2000
    ver=U-Boot 2020.10 (Sep 24 2021 - 05:49:07 +0000)
    
    Environment size: 558/131068 bytes
    => ext4load mmc 0:1 0x48080000 /Image;ext4load mmc 0:1 0x48000000 /r8a77951-ulcb-kf.dtb;booti 0x48080000 - 0x48000000
    24240640 bytes read in 261 ms (88.6 MiB/s)
    125474 bytes read in 3 ms (39.9 MiB/s)
    Moving Image from 0x48080000 to 0x48200000, end=499a0000
    ## Flattened Device Tree blob at 48000000
       Booting using the fdt blob at 0x48000000
       Loading Device Tree to 0000000053fde000, end 0000000053fffa21 ... OK
    
    Starting kernel ...
    
    [    0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd073]
    [    0.000000] Linux version 5.10.41-yocto-standard (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 9.3.0, GNU ld (GNU Binutils) 2.34.0.20200220) #1 SMP PREEMPT Fri Sep 24 05:07:18 UTC 2021
    [    0.000000] Machine model: Renesas H3ULCB Kingfisher board based on r8a77951
    [    0.000000] efi: UEFI not found.
    [    0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB
    [    0.000000] OF: reserved mem: initialized node linux,cma@57000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
    [    0.000000] OF: reserved mem: initialized node linux,multimedia@70000000, compatible id shared-dma-pool
    [    0.000000] NUMA: No NUMA configuration found
    [    0.000000] NUMA: Faking a node at [mem 0x0000000048000000-0x000000077fffffff]
    [    0.000000] NUMA: NODE_DATA [mem 0x77efbbb00-0x77efbdfff]
    [    0.000000] Zone ranges:
    [    0.000000]   DMA      [mem 0x0000000048000000-0x000000007fffffff]
    [    0.000000]   DMA32    [mem 0x0000000080000000-0x00000000ffffffff]
    [    0.000000]   Normal   [mem 0x0000000100000000-0x000000077fffffff]
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x0000000048000000-0x0000000053ffffff]
    [    0.000000]   node   0: [mem 0x0000000054000000-0x0000000056ffffff]
    [    0.000000]   node   0: [mem 0x0000000057000000-0x00000000bfffffff]
    [    0.000000]   node   0: [mem 0x0000000500000000-0x000000057fffffff]
    [    0.000000]   node   0: [mem 0x0000000600000000-0x000000067fffffff]
    [    0.000000]   node   0: [mem 0x0000000700000000-0x000000077fffffff]
    [    0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000077fffffff]
    [    0.000000] psci: probing for conduit method from DT.
    [    0.000000] psci: PSCIv1.1 detected in firmware.
    [    0.000000] psci: Using standard PSCI v0.2 function IDs
    [    0.000000] psci: Trusted OS resident on physical CPU 0x0
    [    0.000000] psci: SMC Calling Convention v1.2
    [    0.000000] percpu: Embedded 23 pages/cpu s55640 r8192 d30376 u94208
    [    0.000000] Detected PIPT I-cache on CPU0
    [    0.000000] CPU features: detected: EL2 vector hardening
    [    0.000000] CPU features: detected: Spectre-v2
    [    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
    [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 2032128
    [    0.000000] Policy zone: Normal
    [    0.000000] Kernel command line: rw root=/dev/mmcblk1p3 rootdelay=5;rw root=/dev/mmcblk1p2 rootdelay=5
    [    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
    [    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
    [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
    [    0.000000] software IO TLB: mapped [mem 0x000000004ffde000-0x0000000053fde000] (64MB)
    [    0.000000] Memory: 7285640K/8257536K available (13632K kernel code, 1272K rwdata, 5780K rodata, 2880K init, 496K bss, 300152K reserved, 671744K cma-reserved)
    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
    [    0.000000] rcu: Preemptible hierarchical RCU implementation.
    [    0.000000] rcu:     RCU event tracing is enabled.
    [    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
    [    0.000000]  Trampoline variant of Tasks RCU enabled.
    [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
    [    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
    [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
    [    0.000000] random: get_random_bytes called from start_kernel+0x32c/0x4ec with crng_init=0
    [    0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt).
    [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns
    [    0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns
    [    0.000159] Console: colour dummy device 80x25
    [    0.000355] printk: console [tty0] enabled
    [    0.000434] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)
    [    0.000450] pid_max: default: 32768 minimum: 301
    [    0.000512] LSM: Security Framework initializing
    [    0.000606] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
    [    0.000657] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
    [    0.002118] rcu: Hierarchical SRCU implementation.
    [    0.003222] Detected Renesas R-Car Gen3 r8a7795 ES3.0
    [    0.004325] EFI services will not be available.
    [    0.004660] smp: Bringing up secondary CPUs ...
    [    0.005092] Detected PIPT I-cache on CPU1
    [    0.005140] CPU1: Booted secondary processor 0x0000000001 [0x411fd073]
    [    0.005601] Detected PIPT I-cache on CPU2
    [    0.005627] CPU2: Booted secondary processor 0x0000000002 [0x411fd073]
    [    0.006035] Detected PIPT I-cache on CPU3
    [    0.006059] CPU3: Booted secondary processor 0x0000000003 [0x411fd073]
    [    0.006454] CPU features: detected: ARM erratum 845719
    [    0.006467] Detected VIPT I-cache on CPU4
    [    0.006516] CPU4: Booted secondary processor 0x0000000100 [0x410fd034]
    [    0.006967] Detected VIPT I-cache on CPU5
    [    0.006994] CPU5: Booted secondary processor 0x0000000101 [0x410fd034]
    [    0.007414] Detected VIPT I-cache on CPU6
    [    0.007441] CPU6: Booted secondary processor 0x0000000102 [0x410fd034]
    [    0.007847] Detected VIPT I-cache on CPU7
    [    0.007875] CPU7: Booted secondary processor 0x0000000103 [0x410fd034]
    [    0.007977] smp: Brought up 1 node, 8 CPUs
    [    0.008040] SMP: Total of 8 processors activated.
    [    0.008047] CPU features: detected: 32-bit EL0 Support
    [    0.008054] CPU features: detected: CRC32 instructions
    [    0.008061] CPU features: detected: 32-bit EL1 Support
    [    0.021479] CPU: All CPU(s) started at EL1
    [    0.021522] alternatives: patching kernel code
    [    0.022802] devtmpfs: initialized
    [    0.031556] KASLR disabled due to lack of seed
    [    0.031706] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
    [    0.031728] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
    [    0.040810] pinctrl core: initialized pinctrl subsystem
    [    0.041338] DMI not present or invalid.
    [    0.041708] NET: Registered protocol family 16
    [    0.042708] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
    [    0.042883] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
    [    0.043180] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
    [    0.043219] audit: initializing netlink subsys (disabled)
    [    0.043400] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
    [    0.043741] thermal_sys: Registered thermal governor 'power_allocator'
    [    0.044739] cpuidle: using governor menu
    [    0.044907] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
    [    0.045031] ASID allocator initialised with 65536 entries
    [    0.045222] Serial: AMBA PL011 UART driver
    [    0.081110] sh-pfc e6060000.pinctrl: r8a77951_pfc support registered
    [    0.089793] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
    [    0.089814] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
    [    0.089823] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
    [    0.089830] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
    [    0.090737] cryptd: max_cpu_qlen set to 1000
    [    0.092661] ACPI: Interpreter disabled.
    [    0.095651] rcar-avs: use avs value: 0
    [    0.095672] rcar-avs: cpu@0 is running with: opp_table0
    [    0.095684] rcar-avs: cpu@1 is running with: opp_table0
    [    0.095692] rcar-avs: cpu@2 is running with: opp_table0
    [    0.095704] rcar-avs: cpu@3 is running with: opp_table0
    [    0.095815] rcar-avs: gsx@fd000000 is running with: gsx_opp_table0
    [    0.097206] iommu: Default domain type: Translated
    [    0.097933] ipmmu-vmsa e67b0000.iommu: IPMMU context 0 is reserved
    [    0.098840] vgaarb: loaded
    [    0.099041] SCSI subsystem initialized
    [    0.099292] usbcore: registered new interface driver usbfs
    [    0.099319] usbcore: registered new interface driver hub
    [    0.099343] usbcore: registered new device driver usb
    [    0.101681] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz
    [    0.102262] mc: Linux media interface: v0.10
    [    0.102284] videodev: Linux video capture interface: v2.00
    [    0.102336] pps_core: LinuxPPS API ver. 1 registered
    [    0.102343] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.102357] PTP clock support registered
    [    0.102499] EDAC MC: Ver: 3.0.0
    [    0.103469] FPGA manager framework
    [    0.103546] Advanced Linux Sound Architecture Driver Initialized.
    [    0.104127] clocksource: Switched to clocksource arch_sys_counter
    [    0.104252] VFS: Disk quotas dquot_6.6.0
    [    0.104298] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [    0.104431] pnp: PnP ACPI: disabled
    [    0.107944] NET: Registered protocol family 2
    [    0.108369] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
    [    0.110591] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
    [    0.110687] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
    [    0.110974] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
    [    0.111581] TCP: Hash tables configured (established 65536 bind 65536)
    [    0.111717] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
    [    0.111830] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
    [    0.112055] NET: Registered protocol family 1
    [    0.112446] RPC: Registered named UNIX socket transport module.
    [    0.112459] RPC: Registered udp transport module.
    [    0.112465] RPC: Registered tcp transport module.
    [    0.112471] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.112485] PCI: CLS 0 bytes, default 64
    [    0.113448] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
    [    0.113721] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available
    [    0.114270] kvm [1]: HYP mode not available
    [    0.117062] Initialise system trusted keyrings
    [    0.117201] workingset: timestamp_bits=42 max_order=21 bucket_order=0
    [    0.120297] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.120693] NFS: Registering the id_resolver key type
    [    0.120714] Key type id_resolver registered
    [    0.120722] Key type id_legacy registered
    [    0.120775] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
    [    0.120784] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
    [    0.120890] 9p: Installing v9fs 9p2000 file system support
    [    0.147007] Key type asymmetric registered
    [    0.147017] Asymmetric key parser 'x509' registered
    [    0.147050] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
    [    0.147061] io scheduler mq-deadline registered
    [    0.147068] io scheduler kyber registered
    [    0.152075] gpio_rcar e6050000.gpio: driving 16 GPIOs
    [    0.152431] gpio_rcar e6051000.gpio: driving 29 GPIOs
    [    0.152610] gpio-455 (BL PWM 100%): hogged as output/high
    [    0.152726] gpio_rcar e6052000.gpio: driving 15 GPIOs
    [    0.153004] gpio_rcar e6053000.gpio: driving 16 GPIOs
    [    0.153186] gpio-432 (MOST RST): hogged as output/high
    [    0.153308] gpio_rcar e6054000.gpio: driving 18 GPIOs
    [    0.153582] gpio_rcar e6055000.gpio: driving 26 GPIOs
    [    0.153752] gpio-381 (Onboard MCh Audio): hogged as output/high
    [    0.153872] gpio_rcar e6055400.gpio: driving 32 GPIOs
    [    0.154133] gpio_rcar e6055800.gpio: driving 4 GPIOs
    [    0.155364] rcar-pcie fe000000.pcie: host bridge /soc/pcie@fe000000 ranges:
    [    0.155392] rcar-pcie fe000000.pcie:       IO 0x00fe100000..0x00fe1fffff -> 0x0000000000
    [    0.155419] rcar-pcie fe000000.pcie:      MEM 0x00fe200000..0x00fe3fffff -> 0x00fe200000
    [    0.155443] rcar-pcie fe000000.pcie:      MEM 0x0030000000..0x0037ffffff -> 0x0030000000
    [    0.155458] rcar-pcie fe000000.pcie:      MEM 0x0038000000..0x003fffffff -> 0x0038000000
    [    0.155476] rcar-pcie fe000000.pcie:   IB MEM 0x0040000000..0x007fffffff -> 0x0040000000
    [    0.155522] rcar-pcie fe000000.pcie: no pcie3v3 regulator found
    [    0.155533] rcar-pcie fe000000.pcie: no pcie1v8 regulator found
    [    0.168867] rcar-pcie fe000000.pcie: PCIe x1: link up
    [    0.180131] rcar-pcie fe000000.pcie: Current link speed is 5 GT/s
    [    0.180220] rcar-pcie fe000000.pcie: PCI host bridge to bus 0000:00
    [    0.180233] pci_bus 0000:00: root bus resource [bus 00-ff]
    [    0.180241] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff]
    [    0.180248] pci_bus 0000:00: root bus resource [mem 0xfe200000-0xfe3fffff]
    [    0.180255] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
    [    0.180263] pci_bus 0000:00: root bus resource [mem 0x38000000-0x3fffffff pref]
    [    0.180293] pci 0000:00:00.0: [1912:0025] type 01 class 0x060400
    [    0.180319] pci 0000:00:00.0: enabling Extended Tags
    [    0.180358] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
    [    0.184451] pci 0000:01:00.0: [144d:a802] type 00 class 0x010802
    [    0.184510] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
    [    0.184533] pci 0000:01:00.0: reg 0x18: [io  0x0000-0x00ff]
    [    0.184847] pci 0000:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0000:00:00.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
    [    0.188345] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
    [    0.188371] pci 0000:00:00.0: BAR 14: assigned [mem 0xfe200000-0xfe2fffff]
    [    0.188381] pci 0000:00:00.0: BAR 13: assigned [io  0x1000-0x1fff]
    [    0.188392] pci 0000:01:00.0: BAR 0: assigned [mem 0xfe200000-0xfe203fff 64bit]
    [    0.188425] pci 0000:01:00.0: BAR 2: assigned [io  0x1000-0x10ff]
    [    0.188441] pci 0000:00:00.0: PCI bridge to [bus 01]
    [    0.188449] pci 0000:00:00.0:   bridge window [io  0x1000-0x1fff]
    [    0.188458] pci 0000:00:00.0:   bridge window [mem 0xfe200000-0xfe2fffff]
    [    0.188541] pcieport 0000:00:00.0: enabling device (0000 -> 0003)
    [    0.188633] pcieport 0000:00:00.0: PME: Signaling with IRQ 234
    [    0.188910] rcar-pcie ee800000.pcie: host bridge /soc/pcie@ee800000 ranges:
    [    0.188932] rcar-pcie ee800000.pcie:       IO 0x00ee900000..0x00ee9fffff -> 0x0000000000
    [    0.188953] rcar-pcie ee800000.pcie:      MEM 0x00eea00000..0x00eebfffff -> 0x00eea00000
    [    0.188972] rcar-pcie ee800000.pcie:      MEM 0x00c0000000..0x00c7ffffff -> 0x00c0000000
    [    0.188986] rcar-pcie ee800000.pcie:      MEM 0x00c8000000..0x00cfffffff -> 0x00c8000000
    [    0.189003] rcar-pcie ee800000.pcie:   IB MEM 0x0040000000..0x007fffffff -> 0x0040000000
    [    0.190724] EINJ: ACPI disabled.
    [    0.209855] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    [    0.211228] SuperH (H)SCI(F) driver initialized
    [    0.211570] e6540000.serial: ttySC1 at MMIO 0xe6540000 (irq = 42, base_baud = 0) is a hscif
    [    0.211741] serial serial0: tty port ttySC1 registered
    [    0.212281] e6550000.serial: ttySC3 at MMIO 0xe6550000 (irq = 43, base_baud = 0) is a hscif
    [    0.212884] e6e68000.serial: ttySC2 at MMIO 0xe6e68000 (irq = 130, base_baud = 0) is a scif
    [    0.213393] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 131, base_baud = 0) is a scif
    [    1.575868] printk: console [ttySC0] enabled
    [    1.586054] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
    [    1.595981] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver
    [    1.611886] loop: module loaded
    [    1.615894] megasas: 07.714.04.00-rc1
    [    1.620623] nvme nvme0: pci function 0000:01:00.0
    [    1.625381] nvme 0000:01:00.0: enabling device (0000 -> 0002)
    [    1.627212] renesas-rpc ee200000.rpc0: using DMA read (dma0chan0)
    [    1.638511] 10 fixed-partitions partitions found on MTD device HyperFlash
    [    1.645342] Creating 10 MTD partitions on "HyperFlash":
    [    1.650577] 0x000000000000-0x000000040000 : "bootparam"
    [    1.656606] nvme nvme0: 7/0/0 default/read/poll queues
    [    1.660701] 0x000000040000-0x000000180000 : "bl2"
    [    1.664725]  nvme0n1: p1 p2
    [    1.668674] 0x000000180000-0x0000001c0000 : "cert_header_sa6"
    [    1.676647] 0x0000001c0000-0x000000200000 : "bl31"
    [    1.684616] 0x000000200000-0x000000640000 : "tee"
    [    1.692633] 0x000000640000-0x000000700000 : "uboot"
    [    1.700624] 0x000000700000-0x000000740000 : "uboot-env"
    [    1.708615] 0x000000740000-0x0000007c0000 : "dtb"
    [    1.716630] 0x0000007c0000-0x000001bc0000 : "kernel"
    [    1.724631] 0x000001bc0000-0x000004000000 : "user"
    [    1.732633] renesas-rpc-hyperflash renesas-rpc-hyperflash: probed flash id:7e0001
    [    1.741830] libphy: Fixed MDIO Bus: probed
    [    1.746644] tun: Universal TUN/TAP device driver, 1.6
    [    1.751825] CAN device driver interface
    [    1.756296] rcar_can e6c30000.can: device registered (IRQ128)
    [    1.762535] rcar_can e6c38000.can: device registered (IRQ129)
    [    1.768866] usbcore: registered new interface driver peak_usb
    [    1.775047] thunder_xcv, ver 1.0
    [    1.778324] thunder_bgx, ver 1.0
    [    1.781578] nicpf, ver 1.0
    [    1.784814] hclge is initializing
    [    1.788145] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
    [    1.795375] hns3: Copyright (c) 2017 Huawei Corporation.
    [    1.800719] e1000: Intel(R) PRO/1000 Network Driver
    [    1.805601] e1000: Copyright (c) 1999-2006 Intel Corporation.
    [    1.811376] e1000e: Intel(R) PRO/1000 Network Driver
    [    1.816344] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
    [    1.822289] igb: Intel(R) Gigabit Ethernet Network Driver
    [    1.827689] igb: Copyright (c) 2007-2014 Intel Corporation.
    [    1.833305] igbvf: Intel(R) Gigabit Virtual Function Network Driver
    [    1.839575] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
    [    1.845511] sky2: driver version 1.30
    [    1.850345] libphy: ravb_mii: probed
    [    1.856795] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:09:0a:06:d2:36, IRQ 125.
    [    1.866402] VFIO - User Level meta-driver version: 0.3
    [    1.872798] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    1.879336] ehci-pci: EHCI PCI platform driver
    [    1.883815] ehci-platform: EHCI generic platform driver
    [    1.916182] ehci-platform ee080100.usb: EHCI Host Controller
    [    1.921863] ehci-platform ee080100.usb: new USB bus registered, assigned bus number 1
    [    1.929743] ehci-platform ee080100.usb: irq 174, io mem 0xee080100
    [    1.948130] ehci-platform ee080100.usb: USB 2.0 started, EHCI 1.10
    [    1.954663] hub 1-0:1.0: USB hub found
    [    1.958439] hub 1-0:1.0: 1 port detected
    [    1.962801] ehci-platform ee0a0100.usb: EHCI Host Controller
    [    1.968490] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 2
    [    1.976388] ehci-platform ee0a0100.usb: irq 175, io mem 0xee0a0100
    [    1.996130] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10
    [    2.002585] hub 2-0:1.0: USB hub found
    [    2.006354] hub 2-0:1.0: 1 port detected
    [    2.010686] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    2.016902] ohci-pci: OHCI PCI platform driver
    [    2.021388] ohci-platform: OHCI generic platform driver
    [    2.026858] ohci-platform ee080000.usb: Generic Platform OHCI controller
    [    2.033577] ohci-platform ee080000.usb: new USB bus registered, assigned bus number 3
    [    2.041453] ohci-platform ee080000.usb: irq 174, io mem 0xee080000
    [    2.134507] hub 3-0:1.0: USB hub found
    [    2.138278] hub 3-0:1.0: 1 port detected
    [    2.142567] ohci-platform ee0a0000.usb: Generic Platform OHCI controller
    [    2.149298] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 4
    [    2.157184] ohci-platform ee0a0000.usb: irq 175, io mem 0xee0a0000
    [    2.250480] hub 4-0:1.0: USB hub found
    [    2.254248] hub 4-0:1.0: 1 port detected
    [    2.258878] xhci-hcd ee000000.usb: xHCI Host Controller
    [    2.264125] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 5
    [    2.287419] xhci-hcd ee000000.usb: hcc params 0x014051ce hci version 0x100 quirks 0x0000000000830410
    [    2.296578] xhci-hcd ee000000.usb: irq 173, io mem 0xee000000
    [    2.302763] hub 5-0:1.0: USB hub found
    [    2.306539] hub 5-0:1.0: 1 port detected
    [    2.310623] xhci-hcd ee000000.usb: xHCI Host Controller
    [    2.315859] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 6
    [    2.323265] xhci-hcd ee000000.usb: Host supports USB 3.0 SuperSpeed
    [    2.329578] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
    [    2.337936] hub 6-0:1.0: USB hub found
    [    2.341704] hub 6-0:1.0: 1 port detected
    [    2.346159] usbcore: registered new interface driver usb-storage
    [    2.353709] renesas_usbhs e6590000.usb: host probed
    [    2.358604] renesas_usbhs e6590000.usb: no transceiver found
    [    2.364352] renesas_usbhs e6590000.usb: gadget probed
    [    2.369569] renesas_usbhs e6590000.usb: probed
    [    2.375199] i2c /dev entries driver
    [    2.388905] cs2000-cp 2-004f: revision - C1
    [    2.394052] pca953x 2-0074: supply vcc not found, using dummy regulator
    [    2.400766] pca953x 2-0074: using no AI
    [    2.406647] gpio-340 (Audio_Out_OFF): hogged as output/high
    [    2.412904] gpio-346 (HUB pwen): hogged as output/high
    [    2.418727] gpio-347 (HUB rst): hogged as output/high
    [    2.425339] gpio-349 (OTG EXTLPn): hogged as output/high
    [    2.431333] gpio-348 (OTG OFFVBUSn): hogged as output/low
    [    2.437413] gpio-355 (SND_RST): hogged as output/high
    [    2.443100] pca953x 2-0075: supply vcc not found, using dummy regulator
    [    2.449777] pca953x 2-0075: using no AI
    [    2.456729] gpio-330 (GPS rst): hogged as output/high
    [    2.462971] gpio-333 (FPDLink shdn): hogged as output/high
    [    2.468672] i2c-rcar e6510000.i2c: probed
    [    2.474591] random: fast init done
    [    2.483531] pca953x 4-0076: supply vcc not found, using dummy regulator
    [    2.490243] pca953x 4-0076: using no AI
    [    2.495289] gpio-308 (Video-B A0): hogged as output/low
    [    2.500802] gpio-309 (Video-B A1): hogged as output/high
    [    2.506375] gpio-310 (Video-A A0): hogged as output/low
    [    2.511861] gpio-311 (Video-A A1): hogged as output/high
    [    2.517584] gpio-318 (RaspB_IO1): hogged as output/high
    [    2.523069] gpio-319 (RaspB_IO0): hogged as output/high
    [    2.528554] gpio-312 (SAM RST): hogged as output/high
    [    2.533865] gpio-313 (SAM PWR): hogged as output/low
    [    2.539088] gpio-322 (LVDS switch): hogged as output/high
    [    2.544830] pca953x 4-0077: supply vcc not found, using dummy regulator
    [    2.551520] pca953x 4-0077: using no AI
    [    2.556104] gpio-292 (mPCIe WAKE#): hogged as output/low
    [    2.561688] gpio-293 (mPCIe W_DISABLE): hogged as output/high
    [    2.567571] gpio-294 (mPCIe CLKREQ#): hogged as input
    [    2.572758] gpio-295 (mPCIe OVC): hogged as input
    [    2.577767] i2c-rcar e66d8000.i2c: probed
    [    2.583248] i2c i2c-2: Added multiplexed i2c bus 9
    [    2.588137] usb 2-1: new high-speed USB device number 2 using ehci-platform
    [    2.588200] i2c i2c-2: Added multiplexed i2c bus 10
    [    2.600133] i2c i2c-2: Added multiplexed i2c bus 11
    [    2.605145] i2c i2c-2: Added multiplexed i2c bus 12
    [    2.610329] adv7511 13-003d: supply avdd not found, using dummy regulator
    [    2.617199] adv7511 13-003d: supply dvdd not found, using dummy regulator
    [    2.624027] adv7511 13-003d: supply pvdd not found, using dummy regulator
    [    2.630862] adv7511 13-003d: supply bgvdd not found, using dummy regulator
    [    2.637773] adv7511 13-003d: supply dvdd-3v not found, using dummy regulator
    [    2.668288] i2c i2c-2: Added multiplexed i2c bus 13
    [    2.673306] i2c i2c-2: Added multiplexed i2c bus 14
    [    2.678484] i2c i2c-2: Added multiplexed i2c bus 15
    [    2.678667] edt_ft5x06 15-0038: supply vcc not found, using dummy regulator
    [    2.683858] i2c i2c-2: Added multiplexed i2c bus 16
    [    2.691211] edt_ft5x06 15-0038: touchscreen probe failed
    [    2.695253] pca954x 2-0071: registered 8 multiplexed busses for I2C switch pca9548
    [    2.708623] i2c i2c-4: Added multiplexed i2c bus 17
    [    2.713943] i2c i2c-4: Added multiplexed i2c bus 18
    [    2.718958] i2c i2c-4: Added multiplexed i2c bus 19
    [    2.723968] i2c i2c-4: Added multiplexed i2c bus 20
    [    2.729212] i2c i2c-4: Added multiplexed i2c bus 21
    [    2.734454] i2c i2c-4: Added multiplexed i2c bus 22
    [    2.739456] i2c i2c-4: Added multiplexed i2c bus 23
    [    2.744916] dummy 24-006c: failed reading
    [    2.749020] i2c i2c-4: Added multiplexed i2c bus 24
    [    2.753910] pca954x 4-0071: registered 8 multiplexed busses for I2C switch pca9548
    [    2.754799] usb-storage 2-1:1.0: USB Mass Storage device detected
    [    2.767880] scsi host0: usb-storage 2-1:1.0
    [    2.920509] usb 6-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
    [    2.949990] hub 6-1:1.0: USB hub found
    [    2.954056] hub 6-1:1.0: 4 ports detected
    [    2.979025] ov5642 22-003c: reg_write: i2c write error, reg: 3103
    [    2.990228] rcar-csi2 fea80000.csi2: 2 lanes found
    [    2.995317] rcar-csi2 feaa0000.csi2: 4 lanes found
    [    3.004605] rcar-vin e6ef0000.video: Device registered as video0
    [    3.010703] rcar-vin e6ef1000.video: Device registered as video1
    [    3.016795] rcar-vin e6ef2000.video: Device registered as video2
    [    3.022878] rcar-vin e6ef3000.video: Device registered as video3
    [    3.028966] rcar-vin e6ef4000.video: Device registered as video4
    [    3.035042] rcar-vin e6ef5000.video: Device registered as video5
    [    3.043120] rcar_gen3_thermal e6198000.thermal: is using FUSE values
    [    3.054415] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points
    [    3.065815] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points
    [    3.077027] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points
    [    3.086422] sdhci: Secure Digital Host Controller Interface driver
    [    3.092641] sdhci: Copyright(c) Pierre Ossman
    [    3.097644] Synopsys Designware Multimedia Card Interface Driver
    [    3.098391] renesas_sdhi_internal_dmac ee140000.mmc: Adding to iommu group 0
    [    3.098432] renesas_sdhi_internal_dmac ee100000.mmc: Got CD GPIO
    [    3.100145] usb 5-1: new high-speed USB device number 2 using xhci-hcd
    [    3.104334] sdhci-pltfm: SDHCI platform and OF driver helper
    [    3.110808] renesas_sdhi_internal_dmac ee140000.mmc: Using IPMMU context 1
    [    3.136084] ledtrig-cpu: registered to indicate activity on CPUs
    [    3.142375] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
    [    3.149180] usbcore: registered new interface driver usbhid
    [    3.154758] usbhid: USB HID core driver
    [    3.159888] optee: probing for conduit method.
    [    3.164358] optee: revision 3.13 (93483d65)
    [    3.164906] optee driver R-Car Rev.1.0.11
    [    3.173580] optee: initialized driver
    [    3.185002] renesas_sdhi_internal_dmac ee140000.mmc: mmc0 base at 0x00000000ee140000, max clock rate 200 MHz
    [    3.192191] rcar_sound ec500000.sound: probed
    [    3.199796] NET: Registered protocol family 17
    [    3.204259] can: controller area network core
    [    3.208686] NET: Registered protocol family 29
    [    3.213137] can: raw protocol
    [    3.216101] can: broadcast manager protocol
    [    3.220290] can: netlink gateway - max_hops=1
    [    3.224807] 9pnet: Installing 9P2000 support
    [    3.229122] Key type dns_resolver registered
    [    3.233844] registered taskstats version 1
    [    3.237953] Loading compiled-in X.509 certificates
    [    3.253115] thermal emergency: set temperature to 110 celsius
    [    3.254249] hub 5-1:1.0: USB hub found
    [    3.259090] thermal emergency: shutdown target cpus 1-7
    [    3.263166] hub 5-1:1.0: 4 ports detected
    [    3.267851] thermal emergency: freq scaled target cpus 0
    [    3.268091] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs
    [    3.281776] mmc0: new HS400 MMC card at address 0001
    [    3.289526] mmcblk0: mmc0:0001 DJUD4R 119 GiB
    [    3.289730] rcar-pcie ee800000.pcie: host bridge /soc/pcie@ee800000 ranges:
    [    3.294335] mmcblk0boot0: mmc0:0001 DJUD4R partition 1 31.9 MiB
    [    3.300976] rcar-pcie ee800000.pcie:       IO 0x00ee900000..0x00ee9fffff -> 0x0000000000
    [    3.307215] mmcblk0boot1: mmc0:0001 DJUD4R partition 2 31.9 MiB
    [    3.314988] rcar-pcie ee800000.pcie:      MEM 0x00eea00000..0x00eebfffff -> 0x00eea00000
    [    3.321201] mmcblk0rpmb: mmc0:0001 DJUD4R partition 3 4.00 MiB, chardev (236:0)
    [    3.329005] rcar-pcie ee800000.pcie:      MEM 0x00c0000000..0x00c7ffffff -> 0x00c0000000
    [    3.338177]  mmcblk0: p1
    [    3.344417] rcar-pcie ee800000.pcie:      MEM 0x00c8000000..0x00cfffffff -> 0x00c8000000
    [    3.355061] rcar-pcie ee800000.pcie:   IB MEM 0x0040000000..0x007fffffff -> 0x0040000000
    [    3.584873] rcar-pcie ee800000.pcie: PCIe x1: link up
    [    3.590564] rcar-pcie ee800000.pcie: PCI host bridge to bus 0001:00
    [    3.596847] pci_bus 0001:00: root bus resource [bus 00-ff]
    [    3.602342] pci_bus 0001:00: root bus resource [io  0x100000-0x1fffff] (bus address [0x0000-0xfffff])
    [    3.611565] pci_bus 0001:00: root bus resource [mem 0xeea00000-0xeebfffff]
    [    3.618442] pci_bus 0001:00: root bus resource [mem 0xc0000000-0xc7ffffff]
    [    3.625319] pci_bus 0001:00: root bus resource [mem 0xc8000000-0xcfffffff pref]
    [    3.632652] pci 0001:00:00.0: [1912:0025] type 01 class 0x060400
    [    3.638681] pci 0001:00:00.0: enabling Extended Tags
    [    3.643680] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
    [    3.653864] pci 0001:01:00.0: [8086:4232] type 00 class 0x028000
    [    3.659959] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
    [    3.667045] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
    [    3.687615] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
    [    3.694257] pci 0001:00:00.0: BAR 14: assigned [mem 0xeea00000-0xeeafffff]
    [    3.701140] pci 0001:01:00.0: BAR 0: assigned [mem 0xeea00000-0xeea01fff 64bit]
    [    3.708495] pci 0001:00:00.0: PCI bridge to [bus 01]
    [    3.713464] pci 0001:00:00.0:   bridge window [mem 0xeea00000-0xeeafffff]
    [    3.720363] pcieport 0001:00:00.0: enabling device (0000 -> 0002)
    [    3.726560] pcieport 0001:00:00.0: PME: Signaling with IRQ 290
    [    3.742617] cpu cpu0: EM: created perf domain
    [    3.747596] cpu cpu4: EM: created perf domain
    [    3.753633] renesas_sdhi_internal_dmac ee100000.mmc: Got CD GPIO
    [    3.783783] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0
    [    3.791558] [drm] Device feb00000.display probed
    [    3.808399] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz
    [    3.882676] renesas_sdhi_internal_dmac ee160000.mmc: mmc2 base at 0x00000000ee160000, max clock rate 50 MHz
    [    3.903636] renesas_sdhi_internal_dmac ee160000.mmc: card claims to support voltages below defined range
    [    3.940201] mmc2: new high speed SDIO card at address 0001
    [    4.018524] mmc1: new ultra high speed SDR104 SDHC card at address aaaa
    [    4.020822] mmcblk1: mmc1:aaaa SC32G 29.7 GiB
    [    4.025263]  mmcblk1: p1 p2 p3
    [    4.055996] Console: switching to colour frame buffer device 160x50
    [    4.106808] rcar-du feb00000.display: [drm] fb0: rcar-dudrmfb frame buffer device
    [    4.119810] input: keyboard as /devices/platform/keyboard/input/input1
    [    4.127409] ALSA device list:
    [    4.130421]   #0: ak4613
    [    4.132982]   #1: pcm3168a
    [    4.135708]   #2: radio
    [    4.138178]   #3: wl18xx
    [    4.141397] Waiting 5 sec before mounting root device...
    [    4.346812] scsi 0:0:0:0: Direct-Access     BUFFALO  USB Flash Disk   1.00 PQ: 0 ANSI: 6
    [    4.358915] sd 0:0:0:0: [sda] 31389312 512-byte logical blocks: (16.1 GB/15.0 GiB)
    [    4.368189] sd 0:0:0:0: [sda] Write Protect is off
    [    4.374042] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [    4.389099]  sda: sda1
    [    4.396307] sd 0:0:0:0: [sda] Attached SCSI removable disk
    [    9.188759] md: Waiting for all devices to be available before autodetect
    [    9.195709] md: If you don't use raid, use raid=noautodetect
    [    9.201516] md: Autodetecting RAID arrays.
    [    9.209602] md: autorun ...
    [    9.216327] md: ... autorun DONE.
    [    9.254085] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
    [    9.267837] VFS: Mounted root (ext4 filesystem) on device 179:98.
    [    9.298830] devtmpfs: mounted
    [    9.306772] Freeing unused kernel memory: 2880K
    [    9.315233] Run /sbin/init as init process
    [    9.664208] systemd[1]: System time before build time, advancing clock.
    [    9.764447] NET: Registered protocol family 10
    [    9.779996] Segment Routing with IPv6
    [    9.847617] systemd[1]: systemd 244.5+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
    [    9.888724] systemd[1]: Detected architecture arm64.
    
    Welcome to Poky (Yocto Project Reference Distro) 3.1.8 (dunfell)!
    
    [    9.975369] systemd[1]: Set hostname to <h3ulcb>.
    [   10.589862] random: systemd: uninitialized urandom read (16 bytes read)
    [   10.600988] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
    [   10.617695] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
    [   10.634322] systemd[1]: Created slice system-getty.slice.
    [  OK  ] Created slice system-getty.slice.
    [   10.660311] random: systemd: uninitialized urandom read (16 bytes read)
    [   10.672949] systemd[1]: Created slice system-serial\x2dgetty.slice.
    [  OK  ] Created slice system-serial\x2dgetty.slice.
    [   10.700415] random: systemd: uninitialized urandom read (16 bytes read)
    [   10.712630] systemd[1]: Created slice User and Session Slice.
    [  OK  ] Created slice User and Session Slice.
    [   10.736562] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [  OK  ] Started Dispatch Password �cts to Console Directory Watch.
    [   10.764468] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [  OK  ] Started Forward Password R�cuests to Wall Directory Watch.
    [   10.792397] systemd[1]: Reached target Paths.
    [  OK  ] Reached target Paths.
    [   10.816534] systemd[1]: Reached target Remote File Systems.
    [  OK  ] Reached target Remote File Systems.
    [   10.840374] systemd[1]: Reached target Slices.
    [  OK  ] Reached target Slices.
    [   10.864458] systemd[1]: Reached target Swap.
    [  OK  ] Reached target Swap.
    [   10.893432] systemd[1]: Listening on RPCbind Server Activation Socket.
    [  OK  ] Listening on RPCbind Server Activation Socket.
    [   10.924507] systemd[1]: Reached target RPC Port Mapper.
    [  OK  ] Reached target RPC Port Mapper.
    [   10.956691] systemd[1]: Listening on Syslog Socket.
    [  OK  ] Listening on Syslog Socket.
    [   10.984973] systemd[1]: Listening on initctl Compatibility Named Pipe.
    [  OK  ] Listening on initctl Compatibility Named Pipe.
    [   11.017626] systemd[1]: Listening on Journal Audit Socket.
    [  OK  ] Listening on Journal Audit Socket.
    [   11.049131] systemd[1]: Listening on Journal Socket (/dev/log).
    [  OK  ] Listening on Journal Socket (/dev/log).
    [   11.081292] systemd[1]: Listening on Journal Socket.
    [  OK  ] Listening on Journal Socket.
    [   11.109665] systemd[1]: Listening on Network Service Netlink Socket.
    [  OK  ] Listening on Network Service Netlink Socket.
    [   11.141297] systemd[1]: Listening on udev Control Socket.
    [  OK  ] Listening on udev Control Socket.
    [   11.172940] systemd[1]: Listening on udev Kernel Socket.
    [  OK  ] Listening on udev Kernel Socket.
    [   11.212218] systemd[1]: Mounting Huge Pages File System...
             Mounting Huge Pages File System...
    [   11.247410] systemd[1]: Mounting POSIX Message Queue File System...
             Mounting POSIX Message Queue File System...
    [   11.287826] systemd[1]: Mounting Kernel Debug File System...
             Mounting Kernel Debug File System...
    [   11.326719] systemd[1]: Mounting Temporary Directory (/tmp)...
             Mounting Temporary Directory (/tmp)...
    [   11.364093] systemd[1]: Starting Create list of static device nodes for the current kernel...
             Starting Create list of st�codes for the current kernel...
    [   11.403439] systemd[1]: Starting Start psplash boot splash screen...
             Starting Start psplash boot splash screen...
    [   11.454090] systemd[1]: Started Hardware RNG Entropy Gatherer Daemon.
    [  OK  ] Started Hardware RNG Entropy Gatherer Daemon.
    [   11.490115] systemd[1]: Starting RPC Bind...
             Starting RPC Bind...
    [   11.516663] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
    [   11.524236] systemd[1]: Starting Journal Service...
             Starting Journal Service...
    [   11.579279] systemd[1]: Starting Load Kernel Modules...
             Starting Load Kernel Modules...
    [   11.599271] cmemdrv: loading out-of-tree module taints kernel.
    [   11.607115] cmem cmem0: DMA mask not set
    [   11.624519] systemd[1]: Starting Remount Root and Kernel File Systems...
             Starting Remount Root and Kernel File Systems...
    [   11.649963] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
    [   11.653095] systemd[1]: Starting udev Coldplug all Devices...
    [   11.653258] cmem cmem0: Memory allocated.. 0x57b00000 (size:0x7000000)
             Starting udev [   11.669669] rgnmm_drv mmngr: assigned reserved memory node linux,multimedia@70000000
    Coldplug all Devices...
    [   11.695160] systemd[1]: Started Start psplash boot splash screen.
    [  OK  ] Started Start psplash boot splash screen.
    [   11.716973] systemd[1]: Started RPC Bind.
    [  OK  ] Started RPC Bind.
    [   11.737159] systemd[1]: Started Journal Service.
    [  OK  ] Started Journal Service.
    [  OK  ] Mounted Huge Pages File System.
    [  OK  ] Mounted POSIX Message Queue File Sy[   11.782155] uio_pdrv_genirq: unknown parameter 'uio_pdrv_genirq' ignored
    stem.
    [  OK  ] Mounted Kernel Debug File System.
    [  OK  ] Mounted Temporary Directory (/tmp).
    [  OK  ] Started Create list of sta�c nodes for the current kernel.
    [  OK  ] Started Load Kernel Modules.
    [  OK  ] Started Remount Root and Kernel File Systems.
             Mounting Kernel Configuration File System...
    [  OK  ] Started Start psplash-syst�cprogress communication helper.
             Starting Flush Journal to Persistent Storage...
    [   11.984560] systemd-journald[319]: Received client request to flush runtime journal.
             Starting Apply Kernel Variables...
             Starting Create Static Device Nodes in /dev...
    [  OK  ] Mounted Kernel Configuration File System.
    [  OK  ] Started Flush Journal to Persistent Storage.
    [  OK  ] Started Apply Kernel Variables.
    [  OK  ] Started Create Static Device Nodes in /dev.
    [  OK  ] Reached target Local File Systems (Pre).
             Mounting /var/volatile...
             Starting udev Kernel Device Manager...
    [  OK  ] Mounted /var/volatile.
             Starting Load/Save Random Seed...
    [  OK  ] Reached target Local File Systems.
             Starting Create Volatile Files and Directories...
    [  OK  ] Started udev Coldplug all Devices.
    [  OK  ] Started udev Kernel Device Manager.
    [  OK  ] Started Create Volatile Files and Directories.
             Starting Network Time Synchronization...
             Starting Update UTMP about System Boot/Shutdown...
    [  OK  ] Started Update UTMP about System Boot/Shutdown.
    [  OK  ] Started Network Time Synchronization.
    [  OK  ] Reached target System Initialization.
    [  OK  ] Started Daily Cleanup of Temporary Directories.
    [  OK  ] Reached target System Time Set.
    [  OK  ] Reached target System Time Synchronized.
    [  OK  ] Reached target Timers.
    [  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Soc[   12.723099] random: crng init done
    [   12.727899] random: 7 urandom warning(s) missed due to ratelimiting
    ket.
    [  OK  ] Listening on D-Bus System Message Bus Socket.
             Starting sshd.socket.
    [  OK  ] Started Load/Save Random Seed.
    [  OK  ] Listening on sshd.socket.
    [   12.860061] ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0
    [  OK  ] Reached target Sockets.
    [  OK  ] Reached target Basic System.
    [  OK  ] Started    12.908571] Bluetooth: Core ver 2.22
    1;39mKernel Logg[   12.913546] NET: Registered protocol family 31
    ing Service.
    [   12.920176] Bluetooth: HCI device and connection manager initialized
    [  OK  ] Started System Logging Service.
    [   12.960335] Bluetooth: HCI socket layer initialized
    [   12.979831] Bluetooth: L2CAP socket layer initialized
    [  OK  ] Started D-Bus System Message Bus.
    [   13.016408] Bluetooth: SCO socket layer initialized
             Starting IPv6 Packet Filtering Framework...
             Starting IPv4 Packet Filtering Framework...
             Starting Telephony service...
    [  OK  ] Started optee services.
    [   13.102958] Bluetooth: HCI UART driver ver 2.3
             Starting PowerVR consumer services...
             Starting rng-tools.service...
             Starting Login Service...
    [  OK  ] Started IPv6 Packet Filtering Framework.
    [   13.179231] Bluetooth: HCI UART protocol H4 registered
    [   13.185079] Bluetooth: HCI UART protocol LL registered
    [   13.191231] Bluetooth: HCI UART protocol Broadcom registered
    [   13.197897] Bluetooth: HCI UART protocol QCA registered
    [   13.207925] st-gyro-i2c 16-006b: supply vdd not found, using dummy regulator
    [   13.208198] ccree e6601000.crypto: ARM ccree device initialized
    [   13.215543] st-gyro-i2c 16-006b: supply vddio not found, using dummy regulator
    [  OK  ] Star[   13.230268] st-lsm9ds0-i2c 16-001d: supply vdd not found, using dummy regulator
    ted IPv4 Packet[   13.239791] st-lsm9ds0-i2c 16-001d: supply vddio not found, using dummy regulator
     Filtering Framework.
    [   13.285909] iio iio:device1: registered accelerometer lsm9ds0
    [   13.326042] iio iio:device0: registered gyroscope lsm9ds0_gyro
    [  OK  ] Started rng-tools.service.
    [   13.366799] iio iio:device2: registered magnetometer lsm9ds0
    [   13.396765] Bluetooth: hci0: change remote baud rate command in firmware
    [  OK  ] Started Telephony service.
    [  OK  ] Reached target Network (Pre).
    [   13.523011] PVR_K:  559: Read BVNC 4.46.6.62 from HW device registers
    [  OK  ] Reached target Hardware activated USB gadget.
    [   13.538936] PVR_K:  559: RGX Device registered with BVNC 4.46.6.62
    [   13.551134] pvrsrvkm fd000000.gsx: Found 4 OPP points.
    [   13.556970] pvrsrvkm fd000000.gsx: opp[1/4]: (200000000 Hz, 830000 uV)
    [   13.564656] pvrsrvkm fd000000.gsx: opp[2/4]: (300000000 Hz, 830000 uV)
    [   13.572218] pvrsrvkm fd000000.gsx: opp[3/4]: (400000000 Hz, 830000 uV)
    [   13.578890] pvrsrvkm fd000000.gsx: opp[4/4]: (600000000 Hz, 830000 uV)
    [   13.578936] DVFS : Changed GPU clock to 600000000 [Hz]
    [   13.591666] [drm] Initialized pvr 1.13.5878540 20170530 for fd000000.gsx on minor 1
             Starting pvrinit.service...
             Starting Network Service...
    [  OK  ] Started Network Service.
    [   13.831250] rcar_sound ec500000.sound: Can't update kctrl when idle
    [  OK  ] Started PowerVR consumer services.
    [   13.879178] Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=266)
    [  OK  ] Started pvrinit.ser[   13.908579] cfg80211: Loading compiled-in X.509 certificates for regulatory database
    vice.
    [   13.926964] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
    [   13.933782] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
    [   13.943010] cfg80211: failed to load regulatory.db
    [  OK  ] Started Login Service.
    [  OK  ] Created slice system-weston.slice.
    [  OK  ] Listening on Load/Save RF �citch Status /dev/rfkill Watch.
             Starting Save/Restore Sound Card State...
    [   14.167445] rcar_sound ec500000.sound: Can't update kctrl when idle
             Starting Bluetooth service...
    [   14.185245] wl18xx_driver wl18xx.6.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2
    [   14.196039] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -2
             Startin[   14.210697] wlcore: WARNING falling back to default config
    g rc.mm.service...
             Starting Network Name Resolution...
    [  OK  ] Started Save/Restore Sound Card State.
    [  OK  ] Started rc.mm.service.
    [  OK  ] Reached target Sound Card.
             Starting set_default_governor.service...
             Starting Load/Save RF Kill Switch Status...
             Starting uim-sysfs.service...
    [  OK  ] Started Load/Save RF Kill Switch Status.
    [   14.399709] (stk) : gpio 343 request failed
    [   14.399747] kim: probe of kim failed with error -16
    [   14.404561] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [   14.414708] Bluetooth: BNEP socket layer initialized
    [   14.421467] rd 0-7: Disabling EAS, schedutil is mandatory
    [  OK  ] Started Network Name Resolution.
    [  OK  ] Started set_default_governor.service.
    [  OK  ] Started Bluetooth service.
    [  OK  ] Reached target Bluetooth.
    [  OK  ] Reached target Network.
    [  OK  ] Reached target Host and Network Name Lookups.
             Starting Avahi mDNS/DNS-SD Stack...
             Starting Hostname Service...
             Starting Permit User Sessions...
             Starting Target Communication Framework agent...
    [  OK  ] Started Permit User Sessions.
    [  OK  ] Started Avahi mDNS/DNS-SD Stack.
    [  OK  ] Started Getty on tty1.
    [  OK  ] Started Serial Getty on ttySC0.
    [   14.725142] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
    [  OK  ] Reached target    14.733743] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.
    ;39mLogin Prompts.
    [   14.746959] wlcore: WARNING This default nvs file can be removed from the file system
    [  OK  ] Started Target Comm[   14.764555] wlcore: loaded
    unication Framework agent.
    [  OK  ] Started Hostname Service.
    [  OK  ] Started uim-sysfs.service.
             Starting pulseaudio.service...
    [  OK  ] Started pulseaudio.service.
    [  OK  ] Reached target Multi-User System.
             Starting Update UTMP about System Runlevel Changes...
    [  OK  ] Started Weston Wayland Compositor.
    [  OK  ] Started Update UTMP about System Runlevel Changes.
    [   15.931864] audit: type=1006 audit(1632460588.263:2): pid=661 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=1 res=1
    [   16.835967] PVR_K:  668: RGX Firmware image 'rgx.fw.4.46.6.62' loaded
    
    Poky (Yocto Project Reference Distro) 3.1.8 h3ulcb ttySC0
    
    h3ulcb login: root
    Last login: Fri Sep 24 05:16:28 UTC 2021
    root@h3ulcb:~#
    root@h3ulcb:~# mount |grep mmcblk
    /dev/mmcblk1p2 on / type ext4 (rw,relatime)
    root@h3ulcb:~#

Reply
  • Hi,

    I tried to reproduce it.

    The kernel booted without any problems.

    Please check the attached file for the boot log and how to reproduce it.

    If the reproduction method is wrong, please point out what is wrong.

    bootlog.txt
    Environments:
     H3 v3 Starter kit(RTP0RC77951SKBX010SA03) + Kingfisher
     Yocto BSP v5.5.0
    
     SD partition:
      0 : Image and r8a77951-ulcb-kf.dtb
      1 : rootfs
      2 : empty
    
     U-boot parameters:
    => setenv bootargs_emmc2 'rw root=/dev/mmcblk1p2 rootdelay=5'
    => setenv bootargs_emmc3 'rw root=/dev/mmcblk1p3 rootdelay=5'
    => setenv bootargs "${bootargs_emmc3};${bootargs_emmc2}"
    => ext4load mmc 0:1 0x48080000 /Image;ext4load mmc 0:1 0x48000000 /r8a77951-ulcb-kf.dtb;booti 0x48080000 - 0x48000000
    
    
    ---- boot log ---
    NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.3.0.2
    NOTICE:  BL2: PRR is R-Car H3 Ver.3.0
    NOTICE:  BL2: Board is Starter Kit Premier Rev.2.1
    NOTICE:  BL2: Boot device is HyperFlash(80MHz)
    NOTICE:  BL2: LCM state is CM
    NOTICE:  AVS setting succeeded. DVFS_SetVID=0x53
    NOTICE:  BL2: DDR3200(rev.0.41)
    NOTICE:  BL2: [COLD_BOOT]
    NOTICE:  BL2: DRAM Split is 4ch(DDR f)
    NOTICE:  BL2: QoS is default setting(rev.0.11)
    NOTICE:  BL2: DRAM refresh interval 1.95 usec
    NOTICE:  BL2: Periodic Write DQ Training
    NOTICE:  BL2: CH0: 400000000 - 47fffffff, 2 GiB
    NOTICE:  BL2: CH1: 500000000 - 57fffffff, 2 GiB
    NOTICE:  BL2: CH2: 600000000 - 67fffffff, 2 GiB
    NOTICE:  BL2: CH3: 700000000 - 77fffffff, 2 GiB
    NOTICE:  BL2: Lossy Decomp areas
    NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
    NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
    NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
    NOTICE:  BL2: FDT at 0xe6326f70
    NOTICE:  BL2: v2.5(release):ca03ad6-dirty
    NOTICE:  BL2: Built : 05:49:00, Sep 24 2021
    NOTICE:  BL2: Normal boot
    NOTICE:  BL2: dst=0xe6326800 src=0x8180000 len=512(0x200)
    NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
    NOTICE:  rcar_file_len: len: 0x0003e000
    NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=253952(0x3e000)
    NOTICE:  rcar_file_len: len: 0x00200000
    NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=2097152(0x200000)
    NOTICE:  rcar_file_len: len: 0x00100000
    NOTICE:  BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)
    NOTICE:  BL2: Booting BL31
    
    
    U-Boot 2020.10 (Sep 24 2021 - 05:49:07 +0000)
    
    CPU: Renesas Electronics R8A7795 rev 3.0
    Model: Renesas H3ULCB board based on r8a77950
    DRAM:  7.9 GiB
    RAM Configuration:
    Bank #0: 0x048000000 - 0x0bfffffff, 1.9 GiB
    Bank #1: 0x500000000 - 0x57fffffff, 2 GiB
    Bank #2: 0x600000000 - 0x67fffffff, 2 GiB
    Bank #3: 0x700000000 - 0x77fffffff, 2 GiB
    
    Flash: 64 MiB
    MMC:   sd@ee100000: 0, sd@ee140000: 1
    Loading Environment from MMC... OK
    In:    serial@e6e88000
    Out:   serial@e6e88000
    Err:   serial@e6e88000
    Net:   eth0: ethernet@e6800000
    Hit any key to stop autoboot:  0
    => ext4ls mmc 0:1 /
    <DIR>       4096 .
    <DIR>       4096 ..
    <DIR>      16384 lost+found
            24240640 Image
              125474 r8a77951-ulcb-kf.dtb
    => ext4ls mmc 0:2 /
    <DIR>       4096 .
    <DIR>       4096 ..
    <DIR>      16384 lost+found
    <DIR>       4096 bin
    <DIR>       4096 boot
    <DIR>       4096 dev
    <DIR>       4096 etc
    <DIR>       4096 home
    <DIR>       4096 lib
    <DIR>       4096 media
    <DIR>       4096 mnt
    <DIR>       4096 proc
    <DIR>       4096 run
    <DIR>       4096 sbin
    <DIR>       4096 sys
    <DIR>       4096 tmp
    <DIR>       4096 usr
    <DIR>       4096 var
    => ext4ls mmc 0:3 /
    <DIR>       4096 .
    <DIR>       4096 ..
    <DIR>      16384 lost+found
    => setenv bootargs_emmc2 'rw root=/dev/mmcblk1p2 rootdelay=5'
    => setenv bootargs_emmc3 'rw root=/dev/mmcblk1p3 rootdelay=5'
    => setenv bootargs "${bootargs_emmc3};${bootargs_emmc2}"
    => printenv
    baudrate=115200
    bootargs=rw root=/dev/mmcblk1p3 rootdelay=5;rw root=/dev/mmcblk1p2 rootdelay=5
    bootargs_emmc2=rw root=/dev/mmcblk1p2 rootdelay=5
    bootargs_emmc3=rw root=/dev/mmcblk1p3 rootdelay=5
    bootcmd=tftp 0x48080000 Image; tftp 0x48000000 Image-r8a77950-ulcb.dtb; booti 0x48080000 - 0x48000000
    bootdelay=2
    bootm_size=0x10000000
    ethaddr=2e:09:0a:06:d2:36
    fdtcontroladdr=bbeed350
    loadaddr=0x58000000
    platform=r8a7795
    stderr=serial@e6e88000
    stdin=serial@e6e88000
    stdout=serial@e6e88000
    usb_pgood_delay=2000
    ver=U-Boot 2020.10 (Sep 24 2021 - 05:49:07 +0000)
    
    Environment size: 558/131068 bytes
    => ext4load mmc 0:1 0x48080000 /Image;ext4load mmc 0:1 0x48000000 /r8a77951-ulcb-kf.dtb;booti 0x48080000 - 0x48000000
    24240640 bytes read in 261 ms (88.6 MiB/s)
    125474 bytes read in 3 ms (39.9 MiB/s)
    Moving Image from 0x48080000 to 0x48200000, end=499a0000
    ## Flattened Device Tree blob at 48000000
       Booting using the fdt blob at 0x48000000
       Loading Device Tree to 0000000053fde000, end 0000000053fffa21 ... OK
    
    Starting kernel ...
    
    [    0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd073]
    [    0.000000] Linux version 5.10.41-yocto-standard (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 9.3.0, GNU ld (GNU Binutils) 2.34.0.20200220) #1 SMP PREEMPT Fri Sep 24 05:07:18 UTC 2021
    [    0.000000] Machine model: Renesas H3ULCB Kingfisher board based on r8a77951
    [    0.000000] efi: UEFI not found.
    [    0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB
    [    0.000000] OF: reserved mem: initialized node linux,cma@57000000, compatible id shared-dma-pool
    [    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
    [    0.000000] OF: reserved mem: initialized node linux,multimedia@70000000, compatible id shared-dma-pool
    [    0.000000] NUMA: No NUMA configuration found
    [    0.000000] NUMA: Faking a node at [mem 0x0000000048000000-0x000000077fffffff]
    [    0.000000] NUMA: NODE_DATA [mem 0x77efbbb00-0x77efbdfff]
    [    0.000000] Zone ranges:
    [    0.000000]   DMA      [mem 0x0000000048000000-0x000000007fffffff]
    [    0.000000]   DMA32    [mem 0x0000000080000000-0x00000000ffffffff]
    [    0.000000]   Normal   [mem 0x0000000100000000-0x000000077fffffff]
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x0000000048000000-0x0000000053ffffff]
    [    0.000000]   node   0: [mem 0x0000000054000000-0x0000000056ffffff]
    [    0.000000]   node   0: [mem 0x0000000057000000-0x00000000bfffffff]
    [    0.000000]   node   0: [mem 0x0000000500000000-0x000000057fffffff]
    [    0.000000]   node   0: [mem 0x0000000600000000-0x000000067fffffff]
    [    0.000000]   node   0: [mem 0x0000000700000000-0x000000077fffffff]
    [    0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000077fffffff]
    [    0.000000] psci: probing for conduit method from DT.
    [    0.000000] psci: PSCIv1.1 detected in firmware.
    [    0.000000] psci: Using standard PSCI v0.2 function IDs
    [    0.000000] psci: Trusted OS resident on physical CPU 0x0
    [    0.000000] psci: SMC Calling Convention v1.2
    [    0.000000] percpu: Embedded 23 pages/cpu s55640 r8192 d30376 u94208
    [    0.000000] Detected PIPT I-cache on CPU0
    [    0.000000] CPU features: detected: EL2 vector hardening
    [    0.000000] CPU features: detected: Spectre-v2
    [    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
    [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 2032128
    [    0.000000] Policy zone: Normal
    [    0.000000] Kernel command line: rw root=/dev/mmcblk1p3 rootdelay=5;rw root=/dev/mmcblk1p2 rootdelay=5
    [    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
    [    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
    [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
    [    0.000000] software IO TLB: mapped [mem 0x000000004ffde000-0x0000000053fde000] (64MB)
    [    0.000000] Memory: 7285640K/8257536K available (13632K kernel code, 1272K rwdata, 5780K rodata, 2880K init, 496K bss, 300152K reserved, 671744K cma-reserved)
    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
    [    0.000000] rcu: Preemptible hierarchical RCU implementation.
    [    0.000000] rcu:     RCU event tracing is enabled.
    [    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
    [    0.000000]  Trampoline variant of Tasks RCU enabled.
    [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
    [    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
    [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
    [    0.000000] random: get_random_bytes called from start_kernel+0x32c/0x4ec with crng_init=0
    [    0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt).
    [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns
    [    0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns
    [    0.000159] Console: colour dummy device 80x25
    [    0.000355] printk: console [tty0] enabled
    [    0.000434] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)
    [    0.000450] pid_max: default: 32768 minimum: 301
    [    0.000512] LSM: Security Framework initializing
    [    0.000606] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
    [    0.000657] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
    [    0.002118] rcu: Hierarchical SRCU implementation.
    [    0.003222] Detected Renesas R-Car Gen3 r8a7795 ES3.0
    [    0.004325] EFI services will not be available.
    [    0.004660] smp: Bringing up secondary CPUs ...
    [    0.005092] Detected PIPT I-cache on CPU1
    [    0.005140] CPU1: Booted secondary processor 0x0000000001 [0x411fd073]
    [    0.005601] Detected PIPT I-cache on CPU2
    [    0.005627] CPU2: Booted secondary processor 0x0000000002 [0x411fd073]
    [    0.006035] Detected PIPT I-cache on CPU3
    [    0.006059] CPU3: Booted secondary processor 0x0000000003 [0x411fd073]
    [    0.006454] CPU features: detected: ARM erratum 845719
    [    0.006467] Detected VIPT I-cache on CPU4
    [    0.006516] CPU4: Booted secondary processor 0x0000000100 [0x410fd034]
    [    0.006967] Detected VIPT I-cache on CPU5
    [    0.006994] CPU5: Booted secondary processor 0x0000000101 [0x410fd034]
    [    0.007414] Detected VIPT I-cache on CPU6
    [    0.007441] CPU6: Booted secondary processor 0x0000000102 [0x410fd034]
    [    0.007847] Detected VIPT I-cache on CPU7
    [    0.007875] CPU7: Booted secondary processor 0x0000000103 [0x410fd034]
    [    0.007977] smp: Brought up 1 node, 8 CPUs
    [    0.008040] SMP: Total of 8 processors activated.
    [    0.008047] CPU features: detected: 32-bit EL0 Support
    [    0.008054] CPU features: detected: CRC32 instructions
    [    0.008061] CPU features: detected: 32-bit EL1 Support
    [    0.021479] CPU: All CPU(s) started at EL1
    [    0.021522] alternatives: patching kernel code
    [    0.022802] devtmpfs: initialized
    [    0.031556] KASLR disabled due to lack of seed
    [    0.031706] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
    [    0.031728] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
    [    0.040810] pinctrl core: initialized pinctrl subsystem
    [    0.041338] DMI not present or invalid.
    [    0.041708] NET: Registered protocol family 16
    [    0.042708] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
    [    0.042883] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
    [    0.043180] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
    [    0.043219] audit: initializing netlink subsys (disabled)
    [    0.043400] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
    [    0.043741] thermal_sys: Registered thermal governor 'power_allocator'
    [    0.044739] cpuidle: using governor menu
    [    0.044907] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
    [    0.045031] ASID allocator initialised with 65536 entries
    [    0.045222] Serial: AMBA PL011 UART driver
    [    0.081110] sh-pfc e6060000.pinctrl: r8a77951_pfc support registered
    [    0.089793] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
    [    0.089814] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
    [    0.089823] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
    [    0.089830] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
    [    0.090737] cryptd: max_cpu_qlen set to 1000
    [    0.092661] ACPI: Interpreter disabled.
    [    0.095651] rcar-avs: use avs value: 0
    [    0.095672] rcar-avs: cpu@0 is running with: opp_table0
    [    0.095684] rcar-avs: cpu@1 is running with: opp_table0
    [    0.095692] rcar-avs: cpu@2 is running with: opp_table0
    [    0.095704] rcar-avs: cpu@3 is running with: opp_table0
    [    0.095815] rcar-avs: gsx@fd000000 is running with: gsx_opp_table0
    [    0.097206] iommu: Default domain type: Translated
    [    0.097933] ipmmu-vmsa e67b0000.iommu: IPMMU context 0 is reserved
    [    0.098840] vgaarb: loaded
    [    0.099041] SCSI subsystem initialized
    [    0.099292] usbcore: registered new interface driver usbfs
    [    0.099319] usbcore: registered new interface driver hub
    [    0.099343] usbcore: registered new device driver usb
    [    0.101681] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz
    [    0.102262] mc: Linux media interface: v0.10
    [    0.102284] videodev: Linux video capture interface: v2.00
    [    0.102336] pps_core: LinuxPPS API ver. 1 registered
    [    0.102343] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.102357] PTP clock support registered
    [    0.102499] EDAC MC: Ver: 3.0.0
    [    0.103469] FPGA manager framework
    [    0.103546] Advanced Linux Sound Architecture Driver Initialized.
    [    0.104127] clocksource: Switched to clocksource arch_sys_counter
    [    0.104252] VFS: Disk quotas dquot_6.6.0
    [    0.104298] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [    0.104431] pnp: PnP ACPI: disabled
    [    0.107944] NET: Registered protocol family 2
    [    0.108369] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
    [    0.110591] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
    [    0.110687] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
    [    0.110974] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
    [    0.111581] TCP: Hash tables configured (established 65536 bind 65536)
    [    0.111717] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
    [    0.111830] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
    [    0.112055] NET: Registered protocol family 1
    [    0.112446] RPC: Registered named UNIX socket transport module.
    [    0.112459] RPC: Registered udp transport module.
    [    0.112465] RPC: Registered tcp transport module.
    [    0.112471] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.112485] PCI: CLS 0 bytes, default 64
    [    0.113448] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
    [    0.113721] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available
    [    0.114270] kvm [1]: HYP mode not available
    [    0.117062] Initialise system trusted keyrings
    [    0.117201] workingset: timestamp_bits=42 max_order=21 bucket_order=0
    [    0.120297] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.120693] NFS: Registering the id_resolver key type
    [    0.120714] Key type id_resolver registered
    [    0.120722] Key type id_legacy registered
    [    0.120775] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
    [    0.120784] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
    [    0.120890] 9p: Installing v9fs 9p2000 file system support
    [    0.147007] Key type asymmetric registered
    [    0.147017] Asymmetric key parser 'x509' registered
    [    0.147050] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
    [    0.147061] io scheduler mq-deadline registered
    [    0.147068] io scheduler kyber registered
    [    0.152075] gpio_rcar e6050000.gpio: driving 16 GPIOs
    [    0.152431] gpio_rcar e6051000.gpio: driving 29 GPIOs
    [    0.152610] gpio-455 (BL PWM 100%): hogged as output/high
    [    0.152726] gpio_rcar e6052000.gpio: driving 15 GPIOs
    [    0.153004] gpio_rcar e6053000.gpio: driving 16 GPIOs
    [    0.153186] gpio-432 (MOST RST): hogged as output/high
    [    0.153308] gpio_rcar e6054000.gpio: driving 18 GPIOs
    [    0.153582] gpio_rcar e6055000.gpio: driving 26 GPIOs
    [    0.153752] gpio-381 (Onboard MCh Audio): hogged as output/high
    [    0.153872] gpio_rcar e6055400.gpio: driving 32 GPIOs
    [    0.154133] gpio_rcar e6055800.gpio: driving 4 GPIOs
    [    0.155364] rcar-pcie fe000000.pcie: host bridge /soc/pcie@fe000000 ranges:
    [    0.155392] rcar-pcie fe000000.pcie:       IO 0x00fe100000..0x00fe1fffff -> 0x0000000000
    [    0.155419] rcar-pcie fe000000.pcie:      MEM 0x00fe200000..0x00fe3fffff -> 0x00fe200000
    [    0.155443] rcar-pcie fe000000.pcie:      MEM 0x0030000000..0x0037ffffff -> 0x0030000000
    [    0.155458] rcar-pcie fe000000.pcie:      MEM 0x0038000000..0x003fffffff -> 0x0038000000
    [    0.155476] rcar-pcie fe000000.pcie:   IB MEM 0x0040000000..0x007fffffff -> 0x0040000000
    [    0.155522] rcar-pcie fe000000.pcie: no pcie3v3 regulator found
    [    0.155533] rcar-pcie fe000000.pcie: no pcie1v8 regulator found
    [    0.168867] rcar-pcie fe000000.pcie: PCIe x1: link up
    [    0.180131] rcar-pcie fe000000.pcie: Current link speed is 5 GT/s
    [    0.180220] rcar-pcie fe000000.pcie: PCI host bridge to bus 0000:00
    [    0.180233] pci_bus 0000:00: root bus resource [bus 00-ff]
    [    0.180241] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff]
    [    0.180248] pci_bus 0000:00: root bus resource [mem 0xfe200000-0xfe3fffff]
    [    0.180255] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
    [    0.180263] pci_bus 0000:00: root bus resource [mem 0x38000000-0x3fffffff pref]
    [    0.180293] pci 0000:00:00.0: [1912:0025] type 01 class 0x060400
    [    0.180319] pci 0000:00:00.0: enabling Extended Tags
    [    0.180358] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
    [    0.184451] pci 0000:01:00.0: [144d:a802] type 00 class 0x010802
    [    0.184510] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
    [    0.184533] pci 0000:01:00.0: reg 0x18: [io  0x0000-0x00ff]
    [    0.184847] pci 0000:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0000:00:00.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
    [    0.188345] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
    [    0.188371] pci 0000:00:00.0: BAR 14: assigned [mem 0xfe200000-0xfe2fffff]
    [    0.188381] pci 0000:00:00.0: BAR 13: assigned [io  0x1000-0x1fff]
    [    0.188392] pci 0000:01:00.0: BAR 0: assigned [mem 0xfe200000-0xfe203fff 64bit]
    [    0.188425] pci 0000:01:00.0: BAR 2: assigned [io  0x1000-0x10ff]
    [    0.188441] pci 0000:00:00.0: PCI bridge to [bus 01]
    [    0.188449] pci 0000:00:00.0:   bridge window [io  0x1000-0x1fff]
    [    0.188458] pci 0000:00:00.0:   bridge window [mem 0xfe200000-0xfe2fffff]
    [    0.188541] pcieport 0000:00:00.0: enabling device (0000 -> 0003)
    [    0.188633] pcieport 0000:00:00.0: PME: Signaling with IRQ 234
    [    0.188910] rcar-pcie ee800000.pcie: host bridge /soc/pcie@ee800000 ranges:
    [    0.188932] rcar-pcie ee800000.pcie:       IO 0x00ee900000..0x00ee9fffff -> 0x0000000000
    [    0.188953] rcar-pcie ee800000.pcie:      MEM 0x00eea00000..0x00eebfffff -> 0x00eea00000
    [    0.188972] rcar-pcie ee800000.pcie:      MEM 0x00c0000000..0x00c7ffffff -> 0x00c0000000
    [    0.188986] rcar-pcie ee800000.pcie:      MEM 0x00c8000000..0x00cfffffff -> 0x00c8000000
    [    0.189003] rcar-pcie ee800000.pcie:   IB MEM 0x0040000000..0x007fffffff -> 0x0040000000
    [    0.190724] EINJ: ACPI disabled.
    [    0.209855] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    [    0.211228] SuperH (H)SCI(F) driver initialized
    [    0.211570] e6540000.serial: ttySC1 at MMIO 0xe6540000 (irq = 42, base_baud = 0) is a hscif
    [    0.211741] serial serial0: tty port ttySC1 registered
    [    0.212281] e6550000.serial: ttySC3 at MMIO 0xe6550000 (irq = 43, base_baud = 0) is a hscif
    [    0.212884] e6e68000.serial: ttySC2 at MMIO 0xe6e68000 (irq = 130, base_baud = 0) is a scif
    [    0.213393] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 131, base_baud = 0) is a scif
    [    1.575868] printk: console [ttySC0] enabled
    [    1.586054] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
    [    1.595981] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver
    [    1.611886] loop: module loaded
    [    1.615894] megasas: 07.714.04.00-rc1
    [    1.620623] nvme nvme0: pci function 0000:01:00.0
    [    1.625381] nvme 0000:01:00.0: enabling device (0000 -> 0002)
    [    1.627212] renesas-rpc ee200000.rpc0: using DMA read (dma0chan0)
    [    1.638511] 10 fixed-partitions partitions found on MTD device HyperFlash
    [    1.645342] Creating 10 MTD partitions on "HyperFlash":
    [    1.650577] 0x000000000000-0x000000040000 : "bootparam"
    [    1.656606] nvme nvme0: 7/0/0 default/read/poll queues
    [    1.660701] 0x000000040000-0x000000180000 : "bl2"
    [    1.664725]  nvme0n1: p1 p2
    [    1.668674] 0x000000180000-0x0000001c0000 : "cert_header_sa6"
    [    1.676647] 0x0000001c0000-0x000000200000 : "bl31"
    [    1.684616] 0x000000200000-0x000000640000 : "tee"
    [    1.692633] 0x000000640000-0x000000700000 : "uboot"
    [    1.700624] 0x000000700000-0x000000740000 : "uboot-env"
    [    1.708615] 0x000000740000-0x0000007c0000 : "dtb"
    [    1.716630] 0x0000007c0000-0x000001bc0000 : "kernel"
    [    1.724631] 0x000001bc0000-0x000004000000 : "user"
    [    1.732633] renesas-rpc-hyperflash renesas-rpc-hyperflash: probed flash id:7e0001
    [    1.741830] libphy: Fixed MDIO Bus: probed
    [    1.746644] tun: Universal TUN/TAP device driver, 1.6
    [    1.751825] CAN device driver interface
    [    1.756296] rcar_can e6c30000.can: device registered (IRQ128)
    [    1.762535] rcar_can e6c38000.can: device registered (IRQ129)
    [    1.768866] usbcore: registered new interface driver peak_usb
    [    1.775047] thunder_xcv, ver 1.0
    [    1.778324] thunder_bgx, ver 1.0
    [    1.781578] nicpf, ver 1.0
    [    1.784814] hclge is initializing
    [    1.788145] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
    [    1.795375] hns3: Copyright (c) 2017 Huawei Corporation.
    [    1.800719] e1000: Intel(R) PRO/1000 Network Driver
    [    1.805601] e1000: Copyright (c) 1999-2006 Intel Corporation.
    [    1.811376] e1000e: Intel(R) PRO/1000 Network Driver
    [    1.816344] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
    [    1.822289] igb: Intel(R) Gigabit Ethernet Network Driver
    [    1.827689] igb: Copyright (c) 2007-2014 Intel Corporation.
    [    1.833305] igbvf: Intel(R) Gigabit Virtual Function Network Driver
    [    1.839575] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
    [    1.845511] sky2: driver version 1.30
    [    1.850345] libphy: ravb_mii: probed
    [    1.856795] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:09:0a:06:d2:36, IRQ 125.
    [    1.866402] VFIO - User Level meta-driver version: 0.3
    [    1.872798] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    1.879336] ehci-pci: EHCI PCI platform driver
    [    1.883815] ehci-platform: EHCI generic platform driver
    [    1.916182] ehci-platform ee080100.usb: EHCI Host Controller
    [    1.921863] ehci-platform ee080100.usb: new USB bus registered, assigned bus number 1
    [    1.929743] ehci-platform ee080100.usb: irq 174, io mem 0xee080100
    [    1.948130] ehci-platform ee080100.usb: USB 2.0 started, EHCI 1.10
    [    1.954663] hub 1-0:1.0: USB hub found
    [    1.958439] hub 1-0:1.0: 1 port detected
    [    1.962801] ehci-platform ee0a0100.usb: EHCI Host Controller
    [    1.968490] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 2
    [    1.976388] ehci-platform ee0a0100.usb: irq 175, io mem 0xee0a0100
    [    1.996130] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10
    [    2.002585] hub 2-0:1.0: USB hub found
    [    2.006354] hub 2-0:1.0: 1 port detected
    [    2.010686] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    2.016902] ohci-pci: OHCI PCI platform driver
    [    2.021388] ohci-platform: OHCI generic platform driver
    [    2.026858] ohci-platform ee080000.usb: Generic Platform OHCI controller
    [    2.033577] ohci-platform ee080000.usb: new USB bus registered, assigned bus number 3
    [    2.041453] ohci-platform ee080000.usb: irq 174, io mem 0xee080000
    [    2.134507] hub 3-0:1.0: USB hub found
    [    2.138278] hub 3-0:1.0: 1 port detected
    [    2.142567] ohci-platform ee0a0000.usb: Generic Platform OHCI controller
    [    2.149298] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 4
    [    2.157184] ohci-platform ee0a0000.usb: irq 175, io mem 0xee0a0000
    [    2.250480] hub 4-0:1.0: USB hub found
    [    2.254248] hub 4-0:1.0: 1 port detected
    [    2.258878] xhci-hcd ee000000.usb: xHCI Host Controller
    [    2.264125] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 5
    [    2.287419] xhci-hcd ee000000.usb: hcc params 0x014051ce hci version 0x100 quirks 0x0000000000830410
    [    2.296578] xhci-hcd ee000000.usb: irq 173, io mem 0xee000000
    [    2.302763] hub 5-0:1.0: USB hub found
    [    2.306539] hub 5-0:1.0: 1 port detected
    [    2.310623] xhci-hcd ee000000.usb: xHCI Host Controller
    [    2.315859] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 6
    [    2.323265] xhci-hcd ee000000.usb: Host supports USB 3.0 SuperSpeed
    [    2.329578] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
    [    2.337936] hub 6-0:1.0: USB hub found
    [    2.341704] hub 6-0:1.0: 1 port detected
    [    2.346159] usbcore: registered new interface driver usb-storage
    [    2.353709] renesas_usbhs e6590000.usb: host probed
    [    2.358604] renesas_usbhs e6590000.usb: no transceiver found
    [    2.364352] renesas_usbhs e6590000.usb: gadget probed
    [    2.369569] renesas_usbhs e6590000.usb: probed
    [    2.375199] i2c /dev entries driver
    [    2.388905] cs2000-cp 2-004f: revision - C1
    [    2.394052] pca953x 2-0074: supply vcc not found, using dummy regulator
    [    2.400766] pca953x 2-0074: using no AI
    [    2.406647] gpio-340 (Audio_Out_OFF): hogged as output/high
    [    2.412904] gpio-346 (HUB pwen): hogged as output/high
    [    2.418727] gpio-347 (HUB rst): hogged as output/high
    [    2.425339] gpio-349 (OTG EXTLPn): hogged as output/high
    [    2.431333] gpio-348 (OTG OFFVBUSn): hogged as output/low
    [    2.437413] gpio-355 (SND_RST): hogged as output/high
    [    2.443100] pca953x 2-0075: supply vcc not found, using dummy regulator
    [    2.449777] pca953x 2-0075: using no AI
    [    2.456729] gpio-330 (GPS rst): hogged as output/high
    [    2.462971] gpio-333 (FPDLink shdn): hogged as output/high
    [    2.468672] i2c-rcar e6510000.i2c: probed
    [    2.474591] random: fast init done
    [    2.483531] pca953x 4-0076: supply vcc not found, using dummy regulator
    [    2.490243] pca953x 4-0076: using no AI
    [    2.495289] gpio-308 (Video-B A0): hogged as output/low
    [    2.500802] gpio-309 (Video-B A1): hogged as output/high
    [    2.506375] gpio-310 (Video-A A0): hogged as output/low
    [    2.511861] gpio-311 (Video-A A1): hogged as output/high
    [    2.517584] gpio-318 (RaspB_IO1): hogged as output/high
    [    2.523069] gpio-319 (RaspB_IO0): hogged as output/high
    [    2.528554] gpio-312 (SAM RST): hogged as output/high
    [    2.533865] gpio-313 (SAM PWR): hogged as output/low
    [    2.539088] gpio-322 (LVDS switch): hogged as output/high
    [    2.544830] pca953x 4-0077: supply vcc not found, using dummy regulator
    [    2.551520] pca953x 4-0077: using no AI
    [    2.556104] gpio-292 (mPCIe WAKE#): hogged as output/low
    [    2.561688] gpio-293 (mPCIe W_DISABLE): hogged as output/high
    [    2.567571] gpio-294 (mPCIe CLKREQ#): hogged as input
    [    2.572758] gpio-295 (mPCIe OVC): hogged as input
    [    2.577767] i2c-rcar e66d8000.i2c: probed
    [    2.583248] i2c i2c-2: Added multiplexed i2c bus 9
    [    2.588137] usb 2-1: new high-speed USB device number 2 using ehci-platform
    [    2.588200] i2c i2c-2: Added multiplexed i2c bus 10
    [    2.600133] i2c i2c-2: Added multiplexed i2c bus 11
    [    2.605145] i2c i2c-2: Added multiplexed i2c bus 12
    [    2.610329] adv7511 13-003d: supply avdd not found, using dummy regulator
    [    2.617199] adv7511 13-003d: supply dvdd not found, using dummy regulator
    [    2.624027] adv7511 13-003d: supply pvdd not found, using dummy regulator
    [    2.630862] adv7511 13-003d: supply bgvdd not found, using dummy regulator
    [    2.637773] adv7511 13-003d: supply dvdd-3v not found, using dummy regulator
    [    2.668288] i2c i2c-2: Added multiplexed i2c bus 13
    [    2.673306] i2c i2c-2: Added multiplexed i2c bus 14
    [    2.678484] i2c i2c-2: Added multiplexed i2c bus 15
    [    2.678667] edt_ft5x06 15-0038: supply vcc not found, using dummy regulator
    [    2.683858] i2c i2c-2: Added multiplexed i2c bus 16
    [    2.691211] edt_ft5x06 15-0038: touchscreen probe failed
    [    2.695253] pca954x 2-0071: registered 8 multiplexed busses for I2C switch pca9548
    [    2.708623] i2c i2c-4: Added multiplexed i2c bus 17
    [    2.713943] i2c i2c-4: Added multiplexed i2c bus 18
    [    2.718958] i2c i2c-4: Added multiplexed i2c bus 19
    [    2.723968] i2c i2c-4: Added multiplexed i2c bus 20
    [    2.729212] i2c i2c-4: Added multiplexed i2c bus 21
    [    2.734454] i2c i2c-4: Added multiplexed i2c bus 22
    [    2.739456] i2c i2c-4: Added multiplexed i2c bus 23
    [    2.744916] dummy 24-006c: failed reading
    [    2.749020] i2c i2c-4: Added multiplexed i2c bus 24
    [    2.753910] pca954x 4-0071: registered 8 multiplexed busses for I2C switch pca9548
    [    2.754799] usb-storage 2-1:1.0: USB Mass Storage device detected
    [    2.767880] scsi host0: usb-storage 2-1:1.0
    [    2.920509] usb 6-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
    [    2.949990] hub 6-1:1.0: USB hub found
    [    2.954056] hub 6-1:1.0: 4 ports detected
    [    2.979025] ov5642 22-003c: reg_write: i2c write error, reg: 3103
    [    2.990228] rcar-csi2 fea80000.csi2: 2 lanes found
    [    2.995317] rcar-csi2 feaa0000.csi2: 4 lanes found
    [    3.004605] rcar-vin e6ef0000.video: Device registered as video0
    [    3.010703] rcar-vin e6ef1000.video: Device registered as video1
    [    3.016795] rcar-vin e6ef2000.video: Device registered as video2
    [    3.022878] rcar-vin e6ef3000.video: Device registered as video3
    [    3.028966] rcar-vin e6ef4000.video: Device registered as video4
    [    3.035042] rcar-vin e6ef5000.video: Device registered as video5
    [    3.043120] rcar_gen3_thermal e6198000.thermal: is using FUSE values
    [    3.054415] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points
    [    3.065815] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points
    [    3.077027] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points
    [    3.086422] sdhci: Secure Digital Host Controller Interface driver
    [    3.092641] sdhci: Copyright(c) Pierre Ossman
    [    3.097644] Synopsys Designware Multimedia Card Interface Driver
    [    3.098391] renesas_sdhi_internal_dmac ee140000.mmc: Adding to iommu group 0
    [    3.098432] renesas_sdhi_internal_dmac ee100000.mmc: Got CD GPIO
    [    3.100145] usb 5-1: new high-speed USB device number 2 using xhci-hcd
    [    3.104334] sdhci-pltfm: SDHCI platform and OF driver helper
    [    3.110808] renesas_sdhi_internal_dmac ee140000.mmc: Using IPMMU context 1
    [    3.136084] ledtrig-cpu: registered to indicate activity on CPUs
    [    3.142375] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
    [    3.149180] usbcore: registered new interface driver usbhid
    [    3.154758] usbhid: USB HID core driver
    [    3.159888] optee: probing for conduit method.
    [    3.164358] optee: revision 3.13 (93483d65)
    [    3.164906] optee driver R-Car Rev.1.0.11
    [    3.173580] optee: initialized driver
    [    3.185002] renesas_sdhi_internal_dmac ee140000.mmc: mmc0 base at 0x00000000ee140000, max clock rate 200 MHz
    [    3.192191] rcar_sound ec500000.sound: probed
    [    3.199796] NET: Registered protocol family 17
    [    3.204259] can: controller area network core
    [    3.208686] NET: Registered protocol family 29
    [    3.213137] can: raw protocol
    [    3.216101] can: broadcast manager protocol
    [    3.220290] can: netlink gateway - max_hops=1
    [    3.224807] 9pnet: Installing 9P2000 support
    [    3.229122] Key type dns_resolver registered
    [    3.233844] registered taskstats version 1
    [    3.237953] Loading compiled-in X.509 certificates
    [    3.253115] thermal emergency: set temperature to 110 celsius
    [    3.254249] hub 5-1:1.0: USB hub found
    [    3.259090] thermal emergency: shutdown target cpus 1-7
    [    3.263166] hub 5-1:1.0: 4 ports detected
    [    3.267851] thermal emergency: freq scaled target cpus 0
    [    3.268091] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs
    [    3.281776] mmc0: new HS400 MMC card at address 0001
    [    3.289526] mmcblk0: mmc0:0001 DJUD4R 119 GiB
    [    3.289730] rcar-pcie ee800000.pcie: host bridge /soc/pcie@ee800000 ranges:
    [    3.294335] mmcblk0boot0: mmc0:0001 DJUD4R partition 1 31.9 MiB
    [    3.300976] rcar-pcie ee800000.pcie:       IO 0x00ee900000..0x00ee9fffff -> 0x0000000000
    [    3.307215] mmcblk0boot1: mmc0:0001 DJUD4R partition 2 31.9 MiB
    [    3.314988] rcar-pcie ee800000.pcie:      MEM 0x00eea00000..0x00eebfffff -> 0x00eea00000
    [    3.321201] mmcblk0rpmb: mmc0:0001 DJUD4R partition 3 4.00 MiB, chardev (236:0)
    [    3.329005] rcar-pcie ee800000.pcie:      MEM 0x00c0000000..0x00c7ffffff -> 0x00c0000000
    [    3.338177]  mmcblk0: p1
    [    3.344417] rcar-pcie ee800000.pcie:      MEM 0x00c8000000..0x00cfffffff -> 0x00c8000000
    [    3.355061] rcar-pcie ee800000.pcie:   IB MEM 0x0040000000..0x007fffffff -> 0x0040000000
    [    3.584873] rcar-pcie ee800000.pcie: PCIe x1: link up
    [    3.590564] rcar-pcie ee800000.pcie: PCI host bridge to bus 0001:00
    [    3.596847] pci_bus 0001:00: root bus resource [bus 00-ff]
    [    3.602342] pci_bus 0001:00: root bus resource [io  0x100000-0x1fffff] (bus address [0x0000-0xfffff])
    [    3.611565] pci_bus 0001:00: root bus resource [mem 0xeea00000-0xeebfffff]
    [    3.618442] pci_bus 0001:00: root bus resource [mem 0xc0000000-0xc7ffffff]
    [    3.625319] pci_bus 0001:00: root bus resource [mem 0xc8000000-0xcfffffff pref]
    [    3.632652] pci 0001:00:00.0: [1912:0025] type 01 class 0x060400
    [    3.638681] pci 0001:00:00.0: enabling Extended Tags
    [    3.643680] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
    [    3.653864] pci 0001:01:00.0: [8086:4232] type 00 class 0x028000
    [    3.659959] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
    [    3.667045] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
    [    3.687615] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
    [    3.694257] pci 0001:00:00.0: BAR 14: assigned [mem 0xeea00000-0xeeafffff]
    [    3.701140] pci 0001:01:00.0: BAR 0: assigned [mem 0xeea00000-0xeea01fff 64bit]
    [    3.708495] pci 0001:00:00.0: PCI bridge to [bus 01]
    [    3.713464] pci 0001:00:00.0:   bridge window [mem 0xeea00000-0xeeafffff]
    [    3.720363] pcieport 0001:00:00.0: enabling device (0000 -> 0002)
    [    3.726560] pcieport 0001:00:00.0: PME: Signaling with IRQ 290
    [    3.742617] cpu cpu0: EM: created perf domain
    [    3.747596] cpu cpu4: EM: created perf domain
    [    3.753633] renesas_sdhi_internal_dmac ee100000.mmc: Got CD GPIO
    [    3.783783] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0
    [    3.791558] [drm] Device feb00000.display probed
    [    3.808399] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz
    [    3.882676] renesas_sdhi_internal_dmac ee160000.mmc: mmc2 base at 0x00000000ee160000, max clock rate 50 MHz
    [    3.903636] renesas_sdhi_internal_dmac ee160000.mmc: card claims to support voltages below defined range
    [    3.940201] mmc2: new high speed SDIO card at address 0001
    [    4.018524] mmc1: new ultra high speed SDR104 SDHC card at address aaaa
    [    4.020822] mmcblk1: mmc1:aaaa SC32G 29.7 GiB
    [    4.025263]  mmcblk1: p1 p2 p3
    [    4.055996] Console: switching to colour frame buffer device 160x50
    [    4.106808] rcar-du feb00000.display: [drm] fb0: rcar-dudrmfb frame buffer device
    [    4.119810] input: keyboard as /devices/platform/keyboard/input/input1
    [    4.127409] ALSA device list:
    [    4.130421]   #0: ak4613
    [    4.132982]   #1: pcm3168a
    [    4.135708]   #2: radio
    [    4.138178]   #3: wl18xx
    [    4.141397] Waiting 5 sec before mounting root device...
    [    4.346812] scsi 0:0:0:0: Direct-Access     BUFFALO  USB Flash Disk   1.00 PQ: 0 ANSI: 6
    [    4.358915] sd 0:0:0:0: [sda] 31389312 512-byte logical blocks: (16.1 GB/15.0 GiB)
    [    4.368189] sd 0:0:0:0: [sda] Write Protect is off
    [    4.374042] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [    4.389099]  sda: sda1
    [    4.396307] sd 0:0:0:0: [sda] Attached SCSI removable disk
    [    9.188759] md: Waiting for all devices to be available before autodetect
    [    9.195709] md: If you don't use raid, use raid=noautodetect
    [    9.201516] md: Autodetecting RAID arrays.
    [    9.209602] md: autorun ...
    [    9.216327] md: ... autorun DONE.
    [    9.254085] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
    [    9.267837] VFS: Mounted root (ext4 filesystem) on device 179:98.
    [    9.298830] devtmpfs: mounted
    [    9.306772] Freeing unused kernel memory: 2880K
    [    9.315233] Run /sbin/init as init process
    [    9.664208] systemd[1]: System time before build time, advancing clock.
    [    9.764447] NET: Registered protocol family 10
    [    9.779996] Segment Routing with IPv6
    [    9.847617] systemd[1]: systemd 244.5+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
    [    9.888724] systemd[1]: Detected architecture arm64.
    
    Welcome to Poky (Yocto Project Reference Distro) 3.1.8 (dunfell)!
    
    [    9.975369] systemd[1]: Set hostname to <h3ulcb>.
    [   10.589862] random: systemd: uninitialized urandom read (16 bytes read)
    [   10.600988] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
    [   10.617695] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
    [   10.634322] systemd[1]: Created slice system-getty.slice.
    [  OK  ] Created slice system-getty.slice.
    [   10.660311] random: systemd: uninitialized urandom read (16 bytes read)
    [   10.672949] systemd[1]: Created slice system-serial\x2dgetty.slice.
    [  OK  ] Created slice system-serial\x2dgetty.slice.
    [   10.700415] random: systemd: uninitialized urandom read (16 bytes read)
    [   10.712630] systemd[1]: Created slice User and Session Slice.
    [  OK  ] Created slice User and Session Slice.
    [   10.736562] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [  OK  ] Started Dispatch Password �cts to Console Directory Watch.
    [   10.764468] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [  OK  ] Started Forward Password R�cuests to Wall Directory Watch.
    [   10.792397] systemd[1]: Reached target Paths.
    [  OK  ] Reached target Paths.
    [   10.816534] systemd[1]: Reached target Remote File Systems.
    [  OK  ] Reached target Remote File Systems.
    [   10.840374] systemd[1]: Reached target Slices.
    [  OK  ] Reached target Slices.
    [   10.864458] systemd[1]: Reached target Swap.
    [  OK  ] Reached target Swap.
    [   10.893432] systemd[1]: Listening on RPCbind Server Activation Socket.
    [  OK  ] Listening on RPCbind Server Activation Socket.
    [   10.924507] systemd[1]: Reached target RPC Port Mapper.
    [  OK  ] Reached target RPC Port Mapper.
    [   10.956691] systemd[1]: Listening on Syslog Socket.
    [  OK  ] Listening on Syslog Socket.
    [   10.984973] systemd[1]: Listening on initctl Compatibility Named Pipe.
    [  OK  ] Listening on initctl Compatibility Named Pipe.
    [   11.017626] systemd[1]: Listening on Journal Audit Socket.
    [  OK  ] Listening on Journal Audit Socket.
    [   11.049131] systemd[1]: Listening on Journal Socket (/dev/log).
    [  OK  ] Listening on Journal Socket (/dev/log).
    [   11.081292] systemd[1]: Listening on Journal Socket.
    [  OK  ] Listening on Journal Socket.
    [   11.109665] systemd[1]: Listening on Network Service Netlink Socket.
    [  OK  ] Listening on Network Service Netlink Socket.
    [   11.141297] systemd[1]: Listening on udev Control Socket.
    [  OK  ] Listening on udev Control Socket.
    [   11.172940] systemd[1]: Listening on udev Kernel Socket.
    [  OK  ] Listening on udev Kernel Socket.
    [   11.212218] systemd[1]: Mounting Huge Pages File System...
             Mounting Huge Pages File System...
    [   11.247410] systemd[1]: Mounting POSIX Message Queue File System...
             Mounting POSIX Message Queue File System...
    [   11.287826] systemd[1]: Mounting Kernel Debug File System...
             Mounting Kernel Debug File System...
    [   11.326719] systemd[1]: Mounting Temporary Directory (/tmp)...
             Mounting Temporary Directory (/tmp)...
    [   11.364093] systemd[1]: Starting Create list of static device nodes for the current kernel...
             Starting Create list of st�codes for the current kernel...
    [   11.403439] systemd[1]: Starting Start psplash boot splash screen...
             Starting Start psplash boot splash screen...
    [   11.454090] systemd[1]: Started Hardware RNG Entropy Gatherer Daemon.
    [  OK  ] Started Hardware RNG Entropy Gatherer Daemon.
    [   11.490115] systemd[1]: Starting RPC Bind...
             Starting RPC Bind...
    [   11.516663] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
    [   11.524236] systemd[1]: Starting Journal Service...
             Starting Journal Service...
    [   11.579279] systemd[1]: Starting Load Kernel Modules...
             Starting Load Kernel Modules...
    [   11.599271] cmemdrv: loading out-of-tree module taints kernel.
    [   11.607115] cmem cmem0: DMA mask not set
    [   11.624519] systemd[1]: Starting Remount Root and Kernel File Systems...
             Starting Remount Root and Kernel File Systems...
    [   11.649963] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
    [   11.653095] systemd[1]: Starting udev Coldplug all Devices...
    [   11.653258] cmem cmem0: Memory allocated.. 0x57b00000 (size:0x7000000)
             Starting udev [   11.669669] rgnmm_drv mmngr: assigned reserved memory node linux,multimedia@70000000
    Coldplug all Devices...
    [   11.695160] systemd[1]: Started Start psplash boot splash screen.
    [  OK  ] Started Start psplash boot splash screen.
    [   11.716973] systemd[1]: Started RPC Bind.
    [  OK  ] Started RPC Bind.
    [   11.737159] systemd[1]: Started Journal Service.
    [  OK  ] Started Journal Service.
    [  OK  ] Mounted Huge Pages File System.
    [  OK  ] Mounted POSIX Message Queue File Sy[   11.782155] uio_pdrv_genirq: unknown parameter 'uio_pdrv_genirq' ignored
    stem.
    [  OK  ] Mounted Kernel Debug File System.
    [  OK  ] Mounted Temporary Directory (/tmp).
    [  OK  ] Started Create list of sta�c nodes for the current kernel.
    [  OK  ] Started Load Kernel Modules.
    [  OK  ] Started Remount Root and Kernel File Systems.
             Mounting Kernel Configuration File System...
    [  OK  ] Started Start psplash-syst�cprogress communication helper.
             Starting Flush Journal to Persistent Storage...
    [   11.984560] systemd-journald[319]: Received client request to flush runtime journal.
             Starting Apply Kernel Variables...
             Starting Create Static Device Nodes in /dev...
    [  OK  ] Mounted Kernel Configuration File System.
    [  OK  ] Started Flush Journal to Persistent Storage.
    [  OK  ] Started Apply Kernel Variables.
    [  OK  ] Started Create Static Device Nodes in /dev.
    [  OK  ] Reached target Local File Systems (Pre).
             Mounting /var/volatile...
             Starting udev Kernel Device Manager...
    [  OK  ] Mounted /var/volatile.
             Starting Load/Save Random Seed...
    [  OK  ] Reached target Local File Systems.
             Starting Create Volatile Files and Directories...
    [  OK  ] Started udev Coldplug all Devices.
    [  OK  ] Started udev Kernel Device Manager.
    [  OK  ] Started Create Volatile Files and Directories.
             Starting Network Time Synchronization...
             Starting Update UTMP about System Boot/Shutdown...
    [  OK  ] Started Update UTMP about System Boot/Shutdown.
    [  OK  ] Started Network Time Synchronization.
    [  OK  ] Reached target System Initialization.
    [  OK  ] Started Daily Cleanup of Temporary Directories.
    [  OK  ] Reached target System Time Set.
    [  OK  ] Reached target System Time Synchronized.
    [  OK  ] Reached target Timers.
    [  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Soc[   12.723099] random: crng init done
    [   12.727899] random: 7 urandom warning(s) missed due to ratelimiting
    ket.
    [  OK  ] Listening on D-Bus System Message Bus Socket.
             Starting sshd.socket.
    [  OK  ] Started Load/Save Random Seed.
    [  OK  ] Listening on sshd.socket.
    [   12.860061] ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0
    [  OK  ] Reached target Sockets.
    [  OK  ] Reached target Basic System.
    [  OK  ] Started    12.908571] Bluetooth: Core ver 2.22
    1;39mKernel Logg[   12.913546] NET: Registered protocol family 31
    ing Service.
    [   12.920176] Bluetooth: HCI device and connection manager initialized
    [  OK  ] Started System Logging Service.
    [   12.960335] Bluetooth: HCI socket layer initialized
    [   12.979831] Bluetooth: L2CAP socket layer initialized
    [  OK  ] Started D-Bus System Message Bus.
    [   13.016408] Bluetooth: SCO socket layer initialized
             Starting IPv6 Packet Filtering Framework...
             Starting IPv4 Packet Filtering Framework...
             Starting Telephony service...
    [  OK  ] Started optee services.
    [   13.102958] Bluetooth: HCI UART driver ver 2.3
             Starting PowerVR consumer services...
             Starting rng-tools.service...
             Starting Login Service...
    [  OK  ] Started IPv6 Packet Filtering Framework.
    [   13.179231] Bluetooth: HCI UART protocol H4 registered
    [   13.185079] Bluetooth: HCI UART protocol LL registered
    [   13.191231] Bluetooth: HCI UART protocol Broadcom registered
    [   13.197897] Bluetooth: HCI UART protocol QCA registered
    [   13.207925] st-gyro-i2c 16-006b: supply vdd not found, using dummy regulator
    [   13.208198] ccree e6601000.crypto: ARM ccree device initialized
    [   13.215543] st-gyro-i2c 16-006b: supply vddio not found, using dummy regulator
    [  OK  ] Star[   13.230268] st-lsm9ds0-i2c 16-001d: supply vdd not found, using dummy regulator
    ted IPv4 Packet[   13.239791] st-lsm9ds0-i2c 16-001d: supply vddio not found, using dummy regulator
     Filtering Framework.
    [   13.285909] iio iio:device1: registered accelerometer lsm9ds0
    [   13.326042] iio iio:device0: registered gyroscope lsm9ds0_gyro
    [  OK  ] Started rng-tools.service.
    [   13.366799] iio iio:device2: registered magnetometer lsm9ds0
    [   13.396765] Bluetooth: hci0: change remote baud rate command in firmware
    [  OK  ] Started Telephony service.
    [  OK  ] Reached target Network (Pre).
    [   13.523011] PVR_K:  559: Read BVNC 4.46.6.62 from HW device registers
    [  OK  ] Reached target Hardware activated USB gadget.
    [   13.538936] PVR_K:  559: RGX Device registered with BVNC 4.46.6.62
    [   13.551134] pvrsrvkm fd000000.gsx: Found 4 OPP points.
    [   13.556970] pvrsrvkm fd000000.gsx: opp[1/4]: (200000000 Hz, 830000 uV)
    [   13.564656] pvrsrvkm fd000000.gsx: opp[2/4]: (300000000 Hz, 830000 uV)
    [   13.572218] pvrsrvkm fd000000.gsx: opp[3/4]: (400000000 Hz, 830000 uV)
    [   13.578890] pvrsrvkm fd000000.gsx: opp[4/4]: (600000000 Hz, 830000 uV)
    [   13.578936] DVFS : Changed GPU clock to 600000000 [Hz]
    [   13.591666] [drm] Initialized pvr 1.13.5878540 20170530 for fd000000.gsx on minor 1
             Starting pvrinit.service...
             Starting Network Service...
    [  OK  ] Started Network Service.
    [   13.831250] rcar_sound ec500000.sound: Can't update kctrl when idle
    [  OK  ] Started PowerVR consumer services.
    [   13.879178] Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=266)
    [  OK  ] Started pvrinit.ser[   13.908579] cfg80211: Loading compiled-in X.509 certificates for regulatory database
    vice.
    [   13.926964] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
    [   13.933782] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
    [   13.943010] cfg80211: failed to load regulatory.db
    [  OK  ] Started Login Service.
    [  OK  ] Created slice system-weston.slice.
    [  OK  ] Listening on Load/Save RF �citch Status /dev/rfkill Watch.
             Starting Save/Restore Sound Card State...
    [   14.167445] rcar_sound ec500000.sound: Can't update kctrl when idle
             Starting Bluetooth service...
    [   14.185245] wl18xx_driver wl18xx.6.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2
    [   14.196039] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -2
             Startin[   14.210697] wlcore: WARNING falling back to default config
    g rc.mm.service...
             Starting Network Name Resolution...
    [  OK  ] Started Save/Restore Sound Card State.
    [  OK  ] Started rc.mm.service.
    [  OK  ] Reached target Sound Card.
             Starting set_default_governor.service...
             Starting Load/Save RF Kill Switch Status...
             Starting uim-sysfs.service...
    [  OK  ] Started Load/Save RF Kill Switch Status.
    [   14.399709] (stk) : gpio 343 request failed
    [   14.399747] kim: probe of kim failed with error -16
    [   14.404561] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [   14.414708] Bluetooth: BNEP socket layer initialized
    [   14.421467] rd 0-7: Disabling EAS, schedutil is mandatory
    [  OK  ] Started Network Name Resolution.
    [  OK  ] Started set_default_governor.service.
    [  OK  ] Started Bluetooth service.
    [  OK  ] Reached target Bluetooth.
    [  OK  ] Reached target Network.
    [  OK  ] Reached target Host and Network Name Lookups.
             Starting Avahi mDNS/DNS-SD Stack...
             Starting Hostname Service...
             Starting Permit User Sessions...
             Starting Target Communication Framework agent...
    [  OK  ] Started Permit User Sessions.
    [  OK  ] Started Avahi mDNS/DNS-SD Stack.
    [  OK  ] Started Getty on tty1.
    [  OK  ] Started Serial Getty on ttySC0.
    [   14.725142] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
    [  OK  ] Reached target    14.733743] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.
    ;39mLogin Prompts.
    [   14.746959] wlcore: WARNING This default nvs file can be removed from the file system
    [  OK  ] Started Target Comm[   14.764555] wlcore: loaded
    unication Framework agent.
    [  OK  ] Started Hostname Service.
    [  OK  ] Started uim-sysfs.service.
             Starting pulseaudio.service...
    [  OK  ] Started pulseaudio.service.
    [  OK  ] Reached target Multi-User System.
             Starting Update UTMP about System Runlevel Changes...
    [  OK  ] Started Weston Wayland Compositor.
    [  OK  ] Started Update UTMP about System Runlevel Changes.
    [   15.931864] audit: type=1006 audit(1632460588.263:2): pid=661 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=1 res=1
    [   16.835967] PVR_K:  668: RGX Firmware image 'rgx.fw.4.46.6.62' loaded
    
    Poky (Yocto Project Reference Distro) 3.1.8 h3ulcb ttySC0
    
    h3ulcb login: root
    Last login: Fri Sep 24 05:16:28 UTC 2021
    root@h3ulcb:~#
    root@h3ulcb:~# mount |grep mmcblk
    /dev/mmcblk1p2 on / type ext4 (rw,relatime)
    root@h3ulcb:~#

Children
No Data