Dear all,
We are developing software with 2 HDMI output, we use starterkit + kingfisher
But we found that the micro HDMI supported resolutions are different between 2 EVBs .
Is there any way to let EVB1 also support 1920*720 resolution?
Thanks
EVB1: No. 2748
root@h3ulcb:~# cat /sys/class/drm/card0-HDMI-A-2/modes1024x768800x600800x600848x480640x480
EVB2: WS3.0 No. 25988
root@h3ulcb:~# cat /sys/class/drm/card0-HDMI-A-2/modes1920x7201920x10801920x10801920x10801920x1080i1920x1080i1920x1080i1920x10801920x1080i1920x10801920x10801366x7681280x7201280x7201280x7201280x7201024x7681024x7681024x768800x600800x600800x600800x600720x576720x576720x480720x480720x480720x480720x480640x480640x480640x480640x480640x480720x400
Hi, Sharon,
1)
Do you have the exact screen plug for the two board?
2)
you can try the tool "edid-decode" to get more information ssh root@$H3_IP cat /sys/class/drm/card0-HDMI-A-1/modes | edid…
you can try the tool "edid-decode" to get more information ssh root@$H3_IP cat /sys/class/drm/card0-HDMI-A-1/modes | edid-decode
For Fedora:
dnf install edid-decode
For Ubuntu (I guess)
apt install edid-decode
On Yocto, you can find "read-edid" (But I never use this recipes).
3)
I do not have a direct solution for that, but my first guess will be to update the firmware on each board.
You can find the documentation here:
elinux.org/.../H3SK
(Using CPLD tools is a good way to update your firmware)
https://elinux.org/R-Car/Boards/H3SK#Flashing_firmware_by_using_CPLD_and_Flash_Writer
Hi Ronan,
Thanks for your reply,
1) Yes, 2 exact screens plugged together
2) Please check the log at the bottom, all of them do not print out 1920x720, but EVB 2 did support this resolution.
3) We use the same firmware and the same SD card to boot the system. (v5.1.0)
EVB1 HDMI-A-1 (Support 1920 * 720)
Extracted contents:header: 31 39 32 30 78 37 32 30serial number: 0a 31 39 32 30 78 31 30 38 30version: 0a 31basic params: 39 32 30 78 31chroma info: 30 38 30 0a 31 33 36 36 78 37established: 36 38 0astandard: 31 32 38 30 78 37 32 30 0a 31 32 38 30 78 37 32descriptor 1: 30 0a 31 32 38 30 78 37 32 30 0a 31 32 38 30 78 37 32descriptor 2: 30 0a 31 30 32 34 78 37 36 38 0a 31 30 32 34 78 37 36descriptor 3: 38 0a 31 30 32 34 78 37 36 38 0a 38 30 30 78 36 30 30descriptor 4: 0a 38 30 30 78 36 30 30 0a 38 30 30 78 36 30 30 0a 38extensions: 30checksum: 30
No header foundManufacturer: BQQ Model 3239 Serial Number 808548400EDID version: 10.49Analog display, Input voltage level: 0.714/0.286 VConfigurable signal levelsSync: Separate Serration Maximum image size: 50 cm x 48 cmGamma: 2.20DPMS levels: OffNon-RGB color displaySupports GTF timings within operating rangeEstablished timings supported: 640x480@60Hz 640x480@67Hz 640x480@75Hz 800x600@56Hz 832x624@75Hz 1280x768@87Hz 1024x768@60HzStandard timings supported: 640x640@110Hz 696x696@108Hz 1208x1208@115Hz 648x648@108Hz 328x328@109Hz 648x648@116Hz 632x474@116Hz 688x688@110HzDetailed mode: Clock 26.080 MHz, 818 mm x 56 mm 817 867 1683 2915 hborder 120 816 816 842 2728 vborder 55 +hsync -vsync digital composite field sequential L/RDetailed mode: Clock 26.080 MHz, 816 mm x 1074 mm 817 871 1695 1377 hborder 120 820 820 846 2732 vborder 55 +hsync +vsync digital composite field sequential L/RDetailed mode: Clock 26.160 MHz, 1840 mm x 2096 mm 817 871 1695 1377 hborder 54 820 852 862 2732 vborder 48 -hsync -vsync digital composite field sequential L/RDetailed mode: Clock 143.460 MHz, 888 mm x 54 mm 1840 1850 2674 3936 hborder 48 822 825 825 870 vborder 10 -hsync -vsync field sequential L/RHas 48 extension blocksChecksum: 0x30 (should be 0x1a)EDID block does not conform at all! Block has broken checksum Bad year of manufacture Bad week of manufacture
EVB1 HDMI-A-2 (Don't support 1920 * 720)
Extracted contents:header: 31 30 32 34 78 37 36 38serial number: 0a 38 30 30 78 36 30 30 0a 38version: 30 30basic params: 78 36 30 30 0achroma info: 38 34 38 78 34 38 30 0a 36 34established: 30 78 34standard: 38 30 0a 00 00 00 00 00 00 00 00 00 00 00 00 00descriptor 1: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00descriptor 2: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00descriptor 3: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00descriptor 4: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00extensions: 00checksum: 00
No header foundManufacturer: BQX Model 3030 Serial Number 808466040EDID version: 48.48Analog display, Input voltage level: 0.7/0.7 VConfigurable signal levelsSync: Separate Maximum image size: 54 cm x 48 cmGamma: 1.48RGB color displayFirst detailed timing is preferred timingEstablished timings supported: 640x480@60Hz 640x480@67Hz 800x600@75Hz 832x624@75Hz 1280x768@87Hz 1024x768@60HzStandard timings supported: 696x696@108Hz 328x328@60Hznon-conformant standard timing (0 horiz)non-conformant standard timing (0 horiz)non-conformant standard timing (0 horiz)non-conformant standard timing (0 horiz)non-conformant standard timing (0 horiz)non-conformant standard timing (0 horiz)Manufacturer-specified data, tag 0Manufacturer-specified data, tag 0Manufacturer-specified data, tag 0Manufacturer-specified data, tag 0Checksum: 0x0 (should be 0x38)EDID block does not conform at all! Block has broken checksum Bad year of manufacture
EVB2 HDMI-A-1 (Support 1920 * 720)
EVB2 HDMI-A-2 (Support 1920 * 720)
Extracted contents:header: 31 39 32 30 78 37 32 30serial number: 0a 31 39 32 30 78 31 30 38 30version: 0a 31basic params: 39 32 30 78 31chroma info: 30 38 30 0a 31 39 32 30 78 31established: 30 38 30standard: 0a 31 39 32 30 78 31 30 38 30 69 0a 31 39 32 30descriptor 1: 78 31 30 38 30 69 0a 31 39 32 30 78 31 30 38 30 69 0adescriptor 2: 31 39 32 30 78 31 30 38 30 0a 31 39 32 30 78 31 30 38descriptor 3: 30 69 0a 31 39 32 30 78 31 30 38 30 0a 31 39 32 30 78descriptor 4: 31 30 38 30 0a 31 33 36 36 78 37 36 38 0a 31 32 38 30extensions: 78checksum: 37
No header foundManufacturer: BQQ Model 3239 Serial Number 808548400EDID version: 10.49Analog display, Input voltage level: 0.714/0.286 VConfigurable signal levelsSync: Separate Serration Maximum image size: 50 cm x 48 cmGamma: 2.20DPMS levels: OffNon-RGB color displaySupports GTF timings within operating rangeEstablished timings supported: 640x480@60Hz 640x480@67Hz 832x624@75Hz 1280x768@87Hz 1024x768@60HzStandard timings supported: 328x328@109Hz 704x704@110Hz 632x474@116Hz 640x640@108Hz 696x696@108Hz 1088x1088@70Hz 640x640@117Hz 648x648@108HzDetailed mode: Clock 126.640 MHz, 817 mm x 2096 mm 816 1129 1947 872 hborder 48 873 908 908 1139 vborder 105 +hsync -vsync bipolar analog composite Detailed mode: Clock 146.410 MHz, 1842 mm x 2096 mm 1842 1890 2668 3938 hborder 49 817 852 869 2913 vborder 48 -hsync -vsync field sequential L/RDetailed mode: Clock 269.280 MHz, 778 mm x 2353 mm 778 827 1643 3131 hborder 50 1842 1845 1853 3938 vborder 48 -hsync -vsync four way interleavedDetailed mode: Clock 123.370 MHz, 824 mm x 266 mm 56 110 998 2664 hborder 50 817 836 875 2404 vborder 56 -hsync -vsync digital composite field sequential L/RHas 120 extension blocksChecksum: 0x37 (should be 0x55)EDID block does not conform at all! Block has broken checksum Bad year of manufacture Bad week of manufacture
Hi Sharon,
I checked H3 v2 SK(S/N 2880) + KF with Yocto v5.1.0.
It was OK.(See the attached log)
- Did you update the loader images(bootparam_sa0.srec, bl2-h3ulcb.srec and etc.) as well as the kernel image?
- Please compare the attached log with your log.
NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.3.0.1 NOTICE: BL2: PRR is R-Car H3 Ver.2.0 NOTICE: BL2: Board is Starter Kit Premier Rev.1.0 NOTICE: BL2: Boot device is HyperFlash(80MHz) NOTICE: BL2: LCM state is CM NOTICE: AVS setting succeeded. DVFS_SetVID=0x53 NOTICE: BL2: DDR3200(rev.0.41) NOTICE: BL2: [COLD_BOOT] NOTICE: BL2: DRAM Split is 4ch NOTICE: BL2: QoS is default setting(rev.0.21) NOTICE: BL2: DRAM refresh interval 1.95 usec NOTICE: BL2: Periodic Write DQ Training NOTICE: BL2: CH0: 400000000 - 43fffffff, 1 GiB NOTICE: BL2: CH1: 500000000 - 53fffffff, 1 GiB NOTICE: BL2: CH2: 600000000 - 63fffffff, 1 GiB NOTICE: BL2: CH3: 700000000 - 73fffffff, 1 GiB NOTICE: BL2: Lossy Decomp areas NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570 NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0 NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0 NOTICE: BL2: FDT at 0xe63267c8 NOTICE: BL2: v2.3():7638cfb-dirty NOTICE: BL2: Built : 12:42:21, Jun 1 2021 NOTICE: BL2: Normal boot NOTICE: BL2: dst=0xe6326300 src=0x8180000 len=512(0x200) NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800) NOTICE: rcar_file_len: len: 0x0003e000 NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=253952(0x3e000) NOTICE: rcar_file_len: len: 0x00200000 NOTICE: BL2: dst=0x44100000 src=0x8200000 len=2097152(0x200000) NOTICE: rcar_file_len: len: 0x00100000 NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000) NOTICE: BL2: Booting BL31 U-Boot 2020.10 (Jun 01 2021 - 12:41:59 +0000) CPU: Renesas Electronics R8A7795 rev 2.0 Model: Renesas H3ULCB board based on r8a77950 DRAM: 3.9 GiB Flash: 64 MiB MMC: sd@ee100000: 0, sd@ee140000: 1 Loading Environment from MMC... OK In: serial@e6e88000 Out: serial@e6e88000 Err: serial@e6e88000 Net: eth0: ethernet@e6800000 Hit any key to stop autoboot: 0 => setenv bootargs consoleblank=0 console=ttySC0,115200 rw root=/dev/sda1 rootwait => usb start;ext4load usb 0 0x48080000 /Image;ext4load usb 0 0x48000000 /r8a77951-ulcb-kf.dtb;booti 0x48080000 - 0x48000000 starting USB... Bus usb@ee0a0100: USB EHCI 1.10 scanning bus usb@ee0a0100 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 24173056 bytes read in 578 ms (39.9 MiB/s) 124954 bytes read in 11 ms (10.8 MiB/s) Moving Image from 0x48080000 to 0x48200000, end=49990000 ## Flattened Device Tree blob at 48000000 Booting using the fdt blob at 0x48000000 Using Device Tree in place at 0000000048000000, end 0000000048021819 Overlap found: 0x500000000..0x53fffffff / 0x500000000..0x53fffffff Overlap found: 0x600000000..0x63fffffff / 0x600000000..0x63fffffff Overlap found: 0x700000000..0x73fffffff / 0x700000000..0x73fffffff Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd073] [ 0.000000] Linux version 5.10.0-yocto-standard (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 9.3.0, GNU ld (GNU Binutils) 2.34.0.20200220) #1 SMP PREEMPT Wed Jun 30 05:44:15 UTC 2021 [ 0.000000] Machine model: Renesas H3ULCB Kingfisher board based on r8a77951 [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma@57000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,multimedia@70000000, compatible id shared-dma-pool [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000048000000-0x000000073fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x73f7bfb00-0x73f7c1fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000048000000-0x000000007fffffff] [ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000073fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000048000000-0x0000000053ffffff] [ 0.000000] node 0: [mem 0x0000000057000000-0x000000007fffffff] [ 0.000000] node 0: [mem 0x0000000500000000-0x000000053fffffff] [ 0.000000] node 0: [mem 0x0000000600000000-0x000000063fffffff] [ 0.000000] node 0: [mem 0x0000000700000000-0x000000073fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000073fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS resident on physical CPU 0x0 [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 23 pages/cpu s55512 r8192 d30504 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 987648 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: consoleblank=0 console=ttySC0,115200 rw root=/dev/sda1 rootwait [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x0000000050000000-0x0000000054000000] (64MB) [ 0.000000] Memory: 3171292K/4014080K available (13568K kernel code, 1270K rwdata, 5784K rodata, 2880K init, 494K bss, 171044K reserved, 671744K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x4ec with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns [ 0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns [ 0.000160] Console: colour dummy device 80x25 [ 0.000233] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333) [ 0.000244] pid_max: default: 32768 minimum: 301 [ 0.000303] LSM: Security Framework initializing [ 0.000363] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.000390] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.001779] rcu: Hierarchical SRCU implementation. [ 0.002853] Detected Renesas R-Car Gen3 r8a7795 ES2.0 [ 0.003937] EFI services will not be available. [ 0.004245] smp: Bringing up secondary CPUs ... [ 0.004650] Detected PIPT I-cache on CPU1 [ 0.004703] CPU1: Booted secondary processor 0x0000000001 [0x411fd073] [ 0.005159] Detected PIPT I-cache on CPU2 [ 0.005182] CPU2: Booted secondary processor 0x0000000002 [0x411fd073] [ 0.005590] Detected PIPT I-cache on CPU3 [ 0.005613] CPU3: Booted secondary processor 0x0000000003 [0x411fd073] [ 0.006002] CPU features: detected: ARM erratum 845719 [ 0.006015] Detected VIPT I-cache on CPU4 [ 0.006061] CPU4: Booted secondary processor 0x0000000100 [0x410fd034] [ 0.006510] Detected VIPT I-cache on CPU5 [ 0.006536] CPU5: Booted secondary processor 0x0000000101 [0x410fd034] [ 0.006945] Detected VIPT I-cache on CPU6 [ 0.006973] CPU6: Booted secondary processor 0x0000000102 [0x410fd034] [ 0.007380] Detected VIPT I-cache on CPU7 [ 0.007407] CPU7: Booted secondary processor 0x0000000103 [0x410fd034] [ 0.007485] smp: Brought up 1 node, 8 CPUs [ 0.007512] SMP: Total of 8 processors activated. [ 0.007518] CPU features: detected: 32-bit EL0 Support [ 0.007523] CPU features: detected: CRC32 instructions [ 0.007528] CPU features: detected: 32-bit EL1 Support [ 0.020542] CPU: All CPU(s) started at EL1 [ 0.020575] alternatives: patching kernel code [ 0.021635] devtmpfs: initialized [ 0.030210] KASLR disabled due to lack of seed [ 0.030513] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.030529] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.038764] pinctrl core: initialized pinctrl subsystem [ 0.039255] DMI not present or invalid. [ 0.039605] NET: Registered protocol family 16 [ 0.040554] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.040638] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.040733] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.040772] audit: initializing netlink subsys (disabled) [ 0.040946] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1 [ 0.041267] thermal_sys: Registered thermal governor 'power_allocator' [ 0.042198] cpuidle: using governor menu [ 0.042353] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.042476] ASID allocator initialised with 65536 entries [ 0.042643] Serial: AMBA PL011 UART driver [ 0.076981] sh-pfc e6060000.pinctrl: r8a77951_pfc support registered [ 0.085217] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.085232] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.085237] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.085242] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.086180] cryptd: max_cpu_qlen set to 1000 [ 0.088088] ACPI: Interpreter disabled. [ 0.092222] iommu: Default domain type: Translated [ 0.092985] ipmmu-vmsa e67b0000.mmu: IPMMU context 0 is reserved [ 0.093867] vgaarb: loaded [ 0.094076] SCSI subsystem initialized [ 0.094327] usbcore: registered new interface driver usbfs [ 0.094350] usbcore: registered new interface driver hub [ 0.094388] usbcore: registered new device driver usb [ 0.096758] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz [ 0.097296] mc: Linux media interface: v0.10 [ 0.097315] videodev: Linux video capture interface: v2.00 [ 0.097359] pps_core: LinuxPPS API ver. 1 registered [ 0.097364] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.097373] PTP clock support registered [ 0.097555] EDAC MC: Ver: 3.0.0 [ 0.098525] FPGA manager framework [ 0.098594] Advanced Linux Sound Architecture Driver Initialized. [ 0.099145] clocksource: Switched to clocksource arch_sys_counter [ 0.099285] VFS: Disk quotas dquot_6.6.0 [ 0.099326] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.099445] pnp: PnP ACPI: disabled [ 0.103002] NET: Registered protocol family 2 [ 0.103324] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.103360] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.103505] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) [ 0.103796] TCP: Hash tables configured (established 32768 bind 32768) [ 0.103904] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 0.103962] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 0.104116] NET: Registered protocol family 1 [ 0.104430] RPC: Registered named UNIX socket transport module. [ 0.104436] RPC: Registered udp transport module. [ 0.104440] RPC: Registered tcp transport module. [ 0.104444] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.104454] PCI: CLS 0 bytes, default 64 [ 0.105352] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 0.105637] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available [ 0.106183] kvm [1]: HYP mode not available [ 0.108989] Initialise system trusted keyrings [ 0.109113] workingset: timestamp_bits=42 max_order=20 bucket_order=0 [ 0.112136] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.112559] NFS: Registering the id_resolver key type [ 0.112576] Key type id_resolver registered [ 0.112581] Key type id_legacy registered [ 0.112633] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.112733] 9p: Installing v9fs 9p2000 file system support [ 0.139189] Key type asymmetric registered [ 0.139196] Asymmetric key parser 'x509' registered [ 0.139222] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 0.139228] io scheduler mq-deadline registered [ 0.139233] io scheduler kyber registered [ 0.144140] gpio_rcar e6050000.gpio: driving 16 GPIOs [ 0.144451] gpio_rcar e6051000.gpio: driving 29 GPIOs [ 0.144633] gpio-455 (BL PWM 100%): hogged as output/high [ 0.144754] gpio_rcar e6052000.gpio: driving 15 GPIOs [ 0.145029] gpio_rcar e6053000.gpio: driving 16 GPIOs [ 0.145195] gpio-432 (MOST RST): hogged as output/high [ 0.145309] gpio_rcar e6054000.gpio: driving 18 GPIOs [ 0.145578] gpio_rcar e6055000.gpio: driving 26 GPIOs [ 0.145741] gpio-381 (Onboard MCh Audio): hogged as output/high [ 0.145850] gpio_rcar e6055400.gpio: driving 32 GPIOs [ 0.146108] gpio_rcar e6055800.gpio: driving 4 GPIOs [ 0.147343] rcar-pcie fe000000.pcie: host bridge /soc/pcie@fe000000 ranges: [ 0.147366] rcar-pcie fe000000.pcie: IO 0x00fe100000..0x00fe1fffff -> 0x0000000000 [ 0.147385] rcar-pcie fe000000.pcie: MEM 0x00fe200000..0x00fe3fffff -> 0x00fe200000 [ 0.147405] rcar-pcie fe000000.pcie: MEM 0x0030000000..0x0037ffffff -> 0x0030000000 [ 0.147416] rcar-pcie fe000000.pcie: MEM 0x0038000000..0x003fffffff -> 0x0038000000 [ 0.147430] rcar-pcie fe000000.pcie: IB MEM 0x0040000000..0x007fffffff -> 0x0040000000 [ 0.147471] rcar-pcie fe000000.pcie: no pcie3v3 regulator found [ 0.147480] rcar-pcie fe000000.pcie: no pcie1v8 regulator found [ 0.163886] rcar-pcie fe000000.pcie: PCIe x1: link up [ 0.175153] rcar-pcie fe000000.pcie: Current link speed is 5 GT/s [ 0.175236] rcar-pcie fe000000.pcie: PCI host bridge to bus 0000:00 [ 0.175245] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.175251] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] [ 0.175256] pci_bus 0000:00: root bus resource [mem 0xfe200000-0xfe3fffff] [ 0.175262] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.175267] pci_bus 0000:00: root bus resource [mem 0x38000000-0x3fffffff pref] [ 0.175292] pci 0000:00:00.0: [1912:0025] type 01 class 0x060400 [ 0.175315] pci 0000:00:00.0: enabling Extended Tags [ 0.175351] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold [ 0.179489] pci 0000:01:00.0: [144d:a802] type 00 class 0x010802 [ 0.179542] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 0.179562] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x00ff] [ 0.179876] pci 0000:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0000:00:00.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link) [ 0.183433] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.183456] pci 0000:00:00.0: BAR 14: assigned [mem 0xfe200000-0xfe2fffff] [ 0.183463] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 0.183472] pci 0000:01:00.0: BAR 0: assigned [mem 0xfe200000-0xfe203fff 64bit] [ 0.183502] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x10ff] [ 0.183515] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.183521] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 0.183527] pci 0000:00:00.0: bridge window [mem 0xfe200000-0xfe2fffff] [ 0.183603] pcieport 0000:00:00.0: enabling device (0000 -> 0003) [ 0.183688] pcieport 0000:00:00.0: PME: Signaling with IRQ 234 [ 0.183967] rcar-pcie ee800000.pcie: host bridge /soc/pcie@ee800000 ranges: [ 0.183988] rcar-pcie ee800000.pcie: IO 0x00ee900000..0x00ee9fffff -> 0x0000000000 [ 0.184006] rcar-pcie ee800000.pcie: MEM 0x00eea00000..0x00eebfffff -> 0x00eea00000 [ 0.184020] rcar-pcie ee800000.pcie: MEM 0x00c0000000..0x00c7ffffff -> 0x00c0000000 [ 0.184031] rcar-pcie ee800000.pcie: MEM 0x00c8000000..0x00cfffffff -> 0x00c8000000 [ 0.184044] rcar-pcie ee800000.pcie: IB MEM 0x0040000000..0x007fffffff -> 0x0040000000 [ 0.185734] EINJ: ACPI disabled. [ 0.203707] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.205035] SuperH (H)SCI(F) driver initialized [ 0.205377] e6540000.serial: ttySC1 at MMIO 0xe6540000 (irq = 42, base_baud = 0) is a hscif [ 0.205534] serial serial0: tty port ttySC1 registered [ 0.205975] e6550000.serial: ttySC3 at MMIO 0xe6550000 (irq = 43, base_baud = 0) is a hscif [ 0.206550] e6e68000.serial: ttySC2 at MMIO 0xe6e68000 (irq = 130, base_baud = 0) is a scif [ 0.207083] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 131, base_baud = 0) is a scif [ 1.511462] printk: console [ttySC0] enabled [ 1.521559] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY) [ 1.531450] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver [ 1.546946] loop: module loaded [ 1.550958] megasas: 07.714.04.00-rc1 [ 1.555646] nvme nvme0: pci function 0000:01:00.0 [ 1.560385] nvme 0000:01:00.0: enabling device (0000 -> 0002) [ 1.562155] renesas-rpc ee200000.rpc0: using DMA read (dma0chan0) [ 1.570823] nvme nvme0: 7/0/0 default/read/poll queues [ 1.573417] 10 fixed-partitions partitions found on MTD device HyperFlash [ 1.580589] nvme0n1: p1 p2 [ 1.584161] Creating 10 MTD partitions on "HyperFlash": [ 1.584173] 0x000000000000-0x000000040000 : "bootparam" [ 1.599700] 0x000000040000-0x000000180000 : "bl2" [ 1.607673] 0x000000180000-0x0000001c0000 : "cert_header_sa6" [ 1.615628] 0x0000001c0000-0x000000200000 : "bl31" [ 1.623632] 0x000000200000-0x000000640000 : "tee" [ 1.631650] 0x000000640000-0x000000700000 : "uboot" [ 1.639635] 0x000000700000-0x000000740000 : "uboot-env" [ 1.647620] 0x000000740000-0x0000007c0000 : "dtb" [ 1.655641] 0x0000007c0000-0x000001bc0000 : "kernel" [ 1.663651] 0x000001bc0000-0x000004000000 : "user" [ 1.671631] renesas-rpc-hyperflash renesas-rpc-hyperflash: probed flash id:7e0001 [ 1.680817] libphy: Fixed MDIO Bus: probed [ 1.685596] tun: Universal TUN/TAP device driver, 1.6 [ 1.690769] CAN device driver interface [ 1.695184] rcar_can e6c30000.can: device registered (IRQ128) [ 1.701388] rcar_can e6c38000.can: device registered (IRQ129) [ 1.707677] usbcore: registered new interface driver peak_usb [ 1.713846] thunder_xcv, ver 1.0 [ 1.717119] thunder_bgx, ver 1.0 [ 1.720373] nicpf, ver 1.0 [ 1.723604] hclge is initializing [ 1.726949] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 1.734177] hns3: Copyright (c) 2017 Huawei Corporation. [ 1.739525] e1000: Intel(R) PRO/1000 Network Driver [ 1.744404] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 1.750169] e1000e: Intel(R) PRO/1000 Network Driver [ 1.755133] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.761079] igb: Intel(R) Gigabit Ethernet Network Driver [ 1.766477] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.772064] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 1.778328] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.784264] sky2: driver version 1.30 [ 1.789147] libphy: ravb_mii: probed [ 1.795459] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:09:0a:02:f3:a6, IRQ 125. [ 1.805025] VFIO - User Level meta-driver version: 0.3 [ 1.811343] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.817873] ehci-pci: EHCI PCI platform driver [ 1.822335] ehci-platform: EHCI generic platform driver [ 1.855210] ehci-platform ee080100.usb: EHCI Host Controller [ 1.860887] ehci-platform ee080100.usb: new USB bus registered, assigned bus number 1 [ 1.868772] ehci-platform ee080100.usb: irq 174, io mem 0xee080100 [ 1.887151] ehci-platform ee080100.usb: USB 2.0 started, EHCI 1.10 [ 1.893683] hub 1-0:1.0: USB hub found [ 1.897451] hub 1-0:1.0: 1 port detected [ 1.901792] ehci-platform ee0a0100.usb: EHCI Host Controller [ 1.907480] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 2 [ 1.915374] ehci-platform ee0a0100.usb: irq 175, io mem 0xee0a0100 [ 1.935151] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10 [ 1.941601] hub 2-0:1.0: USB hub found [ 1.945367] hub 2-0:1.0: 1 port detected [ 1.949686] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.955900] ohci-pci: OHCI PCI platform driver [ 1.960383] ohci-platform: OHCI generic platform driver [ 1.965845] ohci-platform ee080000.usb: Generic Platform OHCI controller [ 1.972560] ohci-platform ee080000.usb: new USB bus registered, assigned bus number 3 [ 1.980434] ohci-platform ee080000.usb: irq 174, io mem 0xee080000 [ 2.074068] hub 3-0:1.0: USB hub found [ 2.077837] hub 3-0:1.0: 1 port detected [ 2.082113] ohci-platform ee0a0000.usb: Generic Platform OHCI controller [ 2.088840] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 4 [ 2.096720] ohci-platform ee0a0000.usb: irq 175, io mem 0xee0a0000 [ 2.190058] hub 4-0:1.0: USB hub found [ 2.193825] hub 4-0:1.0: 1 port detected [ 2.198424] xhci-hcd ee000000.usb: xHCI Host Controller [ 2.203682] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 5 [ 2.226964] xhci-hcd ee000000.usb: hcc params 0x014051ce hci version 0x100 quirks 0x0000000000830410 [ 2.236127] xhci-hcd ee000000.usb: irq 173, io mem 0xee000000 [ 2.242274] hub 5-0:1.0: USB hub found [ 2.246043] hub 5-0:1.0: 1 port detected [ 2.250119] xhci-hcd ee000000.usb: xHCI Host Controller [ 2.255353] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 6 [ 2.262755] xhci-hcd ee000000.usb: Host supports USB 3.0 SuperSpeed [ 2.269060] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.277427] hub 6-0:1.0: USB hub found [ 2.281197] hub 6-0:1.0: 1 port detected [ 2.283158] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 2.285681] usbcore: registered new interface driver usb-storage [ 2.299649] renesas_usbhs e6590000.usb: host probed [ 2.304555] renesas_usbhs e6590000.usb: no transceiver found [ 2.310290] renesas_usbhs e6590000.usb: gadget probed [ 2.315503] renesas_usbhs e6590000.usb: probed [ 2.321088] i2c /dev entries driver [ 2.334834] cs2000-cp 2-004f: revision - C1 [ 2.340008] pca953x 2-0074: supply vcc not found, using dummy regulator [ 2.346696] pca953x 2-0074: using no AI [ 2.352570] gpio-340 (Audio_Out_OFF): hogged as output/high [ 2.358825] gpio-346 (HUB pwen): hogged as output/high [ 2.364642] gpio-347 (HUB rst): hogged as output/high [ 2.371253] gpio-349 (OTG EXTLPn): hogged as output/high [ 2.377245] gpio-348 (OTG OFFVBUSn): hogged as output/low [ 2.383326] gpio-355 (SND_RST): hogged as output/high [ 2.389056] pca953x 2-0075: supply vcc not found, using dummy regulator [ 2.395729] pca953x 2-0075: using no AI [ 2.402677] gpio-330 (GPS rst): hogged as output/high [ 2.408849] gpio-333 (FPDLink shdn): hogged as output/high [ 2.414540] i2c-rcar e6510000.i2c: probed [ 2.420304] random: fast init done [ 2.429273] pca953x 4-0076: supply vcc not found, using dummy regulator [ 2.435970] pca953x 4-0076: using no AI [ 2.440996] gpio-308 (Video-B A0): hogged as output/low [ 2.446481] gpio-309 (Video-B A1): hogged as output/high [ 2.452050] gpio-310 (Video-A A0): hogged as output/low [ 2.457532] gpio-311 (Video-A A1): hogged as output/high [ 2.461938] usb-storage 2-1:1.0: USB Mass Storage device detected [ 2.463253] gpio-318 (RaspB_IO1): hogged as output/high [ 2.469247] scsi host0: usb-storage 2-1:1.0 [ 2.474412] gpio-319 (RaspB_IO0): hogged as output/high [ 2.483825] gpio-312 (SAM RST): hogged as output/high [ 2.489133] gpio-313 (SAM PWR): hogged as output/low [ 2.494354] gpio-322 (LVDS switch): hogged as output/high [ 2.500089] pca953x 4-0077: supply vcc not found, using dummy regulator [ 2.506759] pca953x 4-0077: using no AI [ 2.511349] gpio-292 (mPCIe WAKE#): hogged as output/low [ 2.516923] gpio-293 (mPCIe W_DISABLE): hogged as output/high [ 2.522805] gpio-294 (mPCIe CLKREQ#): hogged as input [ 2.527989] gpio-295 (mPCIe OVC): hogged as input [ 2.533000] i2c-rcar e66d8000.i2c: probed [ 2.538417] i2c i2c-2: Added multiplexed i2c bus 9 [ 2.543352] i2c i2c-2: Added multiplexed i2c bus 10 [ 2.548352] i2c i2c-2: Added multiplexed i2c bus 11 [ 2.553362] i2c i2c-2: Added multiplexed i2c bus 12 [ 2.558529] adv7511 13-003d: supply avdd not found, using dummy regulator [ 2.565403] adv7511 13-003d: supply dvdd not found, using dummy regulator [ 2.572220] adv7511 13-003d: supply pvdd not found, using dummy regulator [ 2.579033] adv7511 13-003d: supply bgvdd not found, using dummy regulator [ 2.585933] adv7511 13-003d: supply dvdd-3v not found, using dummy regulator [ 2.616381] i2c i2c-2: Added multiplexed i2c bus 13 [ 2.621392] i2c i2c-2: Added multiplexed i2c bus 14 [ 2.626545] i2c i2c-2: Added multiplexed i2c bus 15 [ 2.626718] edt_ft5x06 15-0038: supply vcc not found, using dummy regulator [ 2.631951] i2c i2c-2: Added multiplexed i2c bus 16 [ 2.639244] edt_ft5x06 15-0038: touchscreen probe failed [ 2.643282] pca954x 2-0071: registered 8 multiplexed busses for I2C switch pca9548 [ 2.656620] i2c i2c-4: Added multiplexed i2c bus 17 [ 2.661916] i2c i2c-4: Added multiplexed i2c bus 18 [ 2.666928] i2c i2c-4: Added multiplexed i2c bus 19 [ 2.671943] i2c i2c-4: Added multiplexed i2c bus 20 [ 2.677140] i2c i2c-4: Added multiplexed i2c bus 21 [ 2.682375] i2c i2c-4: Added multiplexed i2c bus 22 [ 2.687367] i2c i2c-4: Added multiplexed i2c bus 23 [ 2.692813] dummy 24-006c: failed reading [ 2.696914] i2c i2c-4: Added multiplexed i2c bus 24 [ 2.701798] pca954x 4-0071: registered 8 multiplexed busses for I2C switch pca9548 [ 2.859531] usb 6-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 2.889111] hub 6-1:1.0: USB hub found [ 2.893170] hub 6-1:1.0: 4 ports detected [ 2.921608] ov5642 22-003c: reg_write: i2c write error, reg: 3103 [ 2.932186] rcar-csi2 fea80000.csi2: 2 lanes found [ 2.937263] rcar-csi2 feaa0000.csi2: 4 lanes found [ 2.946515] rcar-vin e6ef0000.video: Device registered as video0 [ 2.952611] rcar-vin e6ef1000.video: Device registered as video1 [ 2.958683] rcar-vin e6ef2000.video: Device registered as video2 [ 2.964782] rcar-vin e6ef3000.video: Device registered as video3 [ 2.970856] rcar-vin e6ef4000.video: Device registered as video4 [ 2.976930] rcar-vin e6ef5000.video: Device registered as video5 [ 2.984925] rcar_gen3_thermal e6198000.thermal: is using pseudo fixed FUSE values [ 2.997304] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points [ 3.008721] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points [ 3.019938] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points [ 3.029277] sdhci: Secure Digital Host Controller Interface driver [ 3.035467] sdhci: Copyright(c) Pierre Ossman [ 3.040504] Synopsys Designware Multimedia Card Interface Driver [ 3.041231] renesas_sdhi_internal_dmac ee100000.mmc: Got CD GPIO [ 3.047180] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.055172] usb 5-1: new high-speed USB device number 2 using xhci-hcd [ 3.065743] ledtrig-cpu: registered to indicate activity on CPUs [ 3.072034] SMCCC: SOC_ID: ARCH_FEATURES(ARCH_SOC_ID) returned error: fffffffffffffffd [ 3.080279] usbcore: registered new interface driver usbhid [ 3.085853] usbhid: USB HID core driver [ 3.090951] optee: probing for conduit method. [ 3.091447] renesas_sdhi_internal_dmac ee140000.mmc: mmc0 base at 0x00000000ee140000, max clock rate 200 MHz [ 3.095412] optee: revision 3.8 (43a5c578) [ 3.105750] optee driver R-Car Rev.1.0.11 [ 3.114273] optee: initialized driver [ 3.131232] rcar_sound ec500000.sound: probed [ 3.136183] NET: Registered protocol family 17 [ 3.140643] can: controller area network core [ 3.145065] NET: Registered protocol family 29 [ 3.149515] can: raw protocol [ 3.152500] can: broadcast manager protocol [ 3.156686] can: netlink gateway - max_hops=1 [ 3.161189] 9pnet: Installing 9P2000 support [ 3.165501] Key type dns_resolver registered [ 3.170134] registered taskstats version 1 [ 3.174239] Loading compiled-in X.509 certificates [ 3.188878] thermal emergency: set temperature to 110 celsius [ 3.194877] thermal emergency: shutdown target cpus 1-7 [ 3.196728] mmc0: new HS400 MMC card at address 0001 [ 3.200103] thermal emergency: freq scaled target cpus 0 [ 3.200383] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs [ 3.205861] mmcblk0: mmc0:0001 8GSD4R 7.28 GiB [ 3.216468] rcar-pcie ee800000.pcie: host bridge /soc/pcie@ee800000 ranges: [ 3.217002] hub 5-1:1.0: USB hub found [ 3.217051] mmcblk0boot0: mmc0:0001 8GSD4R partition 1 31.9 MiB [ 3.217162] mmcblk0boot1: mmc0:0001 8GSD4R partition 2 31.9 MiB [ 3.217437] mmcblk0rpmb: mmc0:0001 8GSD4R partition 3 512 KiB, chardev (236:0) [ 3.221476] rcar-pcie ee800000.pcie: IO 0x00ee900000..0x00ee9fffff -> 0x0000000000 [ 3.221492] rcar-pcie ee800000.pcie: MEM 0x00eea00000..0x00eebfffff -> 0x00eea00000 [ 3.228795] hub 5-1:1.0: 4 ports detected [ 3.232202] rcar-pcie ee800000.pcie: MEM 0x00c0000000..0x00c7ffffff -> 0x00c0000000 [ 3.239407] mmcblk0: p1 [ 3.244042] rcar-pcie ee800000.pcie: MEM 0x00c8000000..0x00cfffffff -> 0x00c8000000 [ 3.244055] rcar-pcie ee800000.pcie: IB MEM 0x0040000000..0x007fffffff -> 0x0040000000 [ 3.519894] rcar-pcie ee800000.pcie: PCIe x1: link up [ 3.525530] rcar-pcie ee800000.pcie: PCI host bridge to bus 0001:00 [ 3.531808] pci_bus 0001:00: root bus resource [bus 00-ff] [ 3.537297] pci_bus 0001:00: root bus resource [io 0x100000-0x1fffff] (bus address [0x0000-0xfffff]) [ 3.546514] pci_bus 0001:00: root bus resource [mem 0xeea00000-0xeebfffff] [ 3.553388] pci_bus 0001:00: root bus resource [mem 0xc0000000-0xc7ffffff] [ 3.560263] pci_bus 0001:00: root bus resource [mem 0xc8000000-0xcfffffff pref] [ 3.567593] pci 0001:00:00.0: [1912:0025] type 01 class 0x060400 [ 3.573618] pci 0001:00:00.0: enabling Extended Tags [ 3.578614] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold [ 3.588862] pci 0001:01:00.0: [8086:4232] type 00 class 0x028000 [ 3.594950] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 3.602035] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 3.622667] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.629304] pci 0001:00:00.0: BAR 14: assigned [mem 0xeea00000-0xeeafffff] [ 3.636185] pci 0001:01:00.0: BAR 0: assigned [mem 0xeea00000-0xeea01fff 64bit] [ 3.643535] pci 0001:00:00.0: PCI bridge to [bus 01] [ 3.648502] pci 0001:00:00.0: bridge window [mem 0xeea00000-0xeeafffff] [ 3.655390] pcieport 0001:00:00.0: enabling device (0000 -> 0002) [ 3.661574] pcieport 0001:00:00.0: PME: Signaling with IRQ 290 [ 3.684974] cpu cpu0: EM: created perf domain [ 3.689934] cpu cpu4: EM: created perf domain [ 3.695560] Failed to set up IOMMU for device ee160000.mmc; retaining platform DMA ops [ 3.695934] Failed to set up IOMMU for device ee100000.mmc; retaining platform DMA ops [ 3.711575] renesas_sdhi_internal_dmac ee100000.mmc: Got CD GPIO [ 3.717789] asoc-audio-graph-card sound@0: ASoC: no DMI vendor name! [ 3.727729] asoc-audio-graph-card sound@1: parse error -22 [ 3.733295] asoc-audio-graph-card: probe of sound@1 failed with error -22 [ 3.740742] asoc-audio-graph-card sound@2: ASoC: no DMI vendor name! [ 3.748099] asoc-audio-graph-card sound@3: ASoC: no DMI vendor name! [ 3.758047] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0 [ 3.765805] [drm] Device feb00000.display probed [ 3.766571] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz [ 3.829675] renesas_sdhi_internal_dmac ee160000.mmc: mmc2 base at 0x00000000ee160000, max clock rate 50 MHz [ 3.848051] renesas_sdhi_internal_dmac ee160000.mmc: card claims to support voltages below defined range [ 3.874678] mmc2: new high speed SDIO card at address 0001 [ 3.972294] Console: switching to colour frame buffer device 160x50 [ 4.014665] rcar-du feb00000.display: [drm] fb0: rcar-dudrmfb frame buffer device [ 4.027479] input: keyboard as /devices/platform/keyboard/input/input1 [ 4.035028] ALSA device list: [ 4.038012] #0: ak4613 [ 4.040548] #1: radio [ 4.042988] #2: wl18xx [ 4.047086] md: Waiting for all devices to be available before autodetect [ 4.053904] md: If you don't use raid, use raid=noautodetect [ 4.059572] md: Autodetecting RAID arrays. [ 4.063680] md: autorun ... [ 4.066511] md: ... autorun DONE. [ 4.069945] Waiting for root device /dev/sda1... [ 4.070097] scsi 0:0:0:0: Direct-Access BUFFALO USB Flash Disk 1.00 PQ: 0 ANSI: 6 [ 4.084256] sd 0:0:0:0: [sda] 61833216 512-byte logical blocks: (31.7 GB/29.5 GiB) [ 4.093792] sd 0:0:0:0: [sda] Write Protect is off [ 4.100503] sd 0:0:0:0: [sda] No Caching mode page found [ 4.105840] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 4.115558] sda: sda1 [ 4.123264] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 4.168388] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 4.176181] VFS: Mounted root (ext4 filesystem) on device 8:1. [ 4.189628] devtmpfs: mounted [ 4.194004] Freeing unused kernel memory: 2880K [ 4.198723] Run /sbin/init as init process [ 4.538647] systemd[1]: System time before build time, advancing clock. [ 4.618743] NET: Registered protocol family 10 [ 4.624746] Segment Routing with IPv6 [ 4.649800] systemd[1]: systemd 244.3+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 4.672452] systemd[1]: Detected architecture arm64. Welcome to Poky (Yocto Project Reference Distro) 3.1.4 (dunfell)! [ 4.715996] systemd[1]: Set hostname to <h3ulcb>. [ 5.196440] random: systemd: uninitialized urandom read (16 bytes read) [ 5.203396] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 5.215777] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 5.227124] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 5.247283] random: systemd: uninitialized urandom read (16 bytes read) [ 5.254910] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 5.275262] random: systemd: uninitialized urandom read (16 bytes read) [ 5.282689] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 5.303459] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password �cts to Console Directory Watch. [ 5.327563] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R�cuests to Wall Directory Watch. [ 5.351452] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 5.371360] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 5.391320] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 5.411331] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 5.850796] systemd[1]: Listening on RPCbind Server Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ 5.875413] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ 5.903500] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 5.923791] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 5.948277] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 5.967865] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 5.991962] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 6.012266] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 6.036025] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 6.055706] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 6.080740] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 6.104540] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 6.132525] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 6.157887] systemd[1]: Mounting Temporary Directory (/tmp)... Mounting Temporary Directory (/tmp)... [ 6.184871] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st�codes for the current kernel... [ 6.216308] systemd[1]: Starting Start psplash boot splash screen... Starting Start psplash boot splash screen... [ 6.246982] systemd[1]: Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ 6.288655] systemd[1]: Starting RPC Bind... Starting RPC Bind... [ 6.307515] systemd[1]: Condition check resulted in File System Check on Root Device being skipped. [ 6.322142] systemd[1]: Starting Journal Service... Starting Journal Service... [ 6.346193] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 6.363466] mmngr: loading out-of-tree module taints kernel. [ 6.371401] rgnmm_drv mmngr: assigned reserved memory node linux,multimedia@70000000 [ 6.383779] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 6.406431] EXT4-fs (sda1): re-mounted. Opts: (null) [ 6.415718] systemd[1]: Starting udev Coldplug all Devices... Starting udev Coldplug all Devices... [ 6.445591] systemd[1]: Started Start psplash boot splash screen. [ OK ] Started Start psplash boot splash screen. [ 6.468028] systemd[1]: Started RPC Bind. [ OK ] Started RPC Bind. [ 6.492039] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ 6.564610] PVR_K: 318: Read BVNC 4.46.6.62 from HW device registers [ 6.571182] PVR_K: 318: RGX Device registered with BVNC 4.46.6.62 [ 6.578395] [drm] Initialized pvr 1.11.5516664 20170530 for fd000000.gsx on minor 1 [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Started Create list of sta�c nodes for the current kernel. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Start psplash-syst�cprogress communication helper. Starting Flush Journal to Persistent Storage... [ 6.688562] systemd-journald[317]: Received client request to flush runtime journal. Starting Create Static Device Nodes in /dev... [ OK ] Started Load Kernel Modules. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Mounting Kernel Configuration File System... Mounting /var/volatile... Starting Apply Kernel Variables... Starting udev Kernel Device Manager... [ OK ] Mounted Kernel Configuration File System. [ OK ] Mounted /var/volatile. [ OK ] Started Apply Kernel Variables. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started udev Coldplug all Devices. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. Starting sshd.socket. [ OK ] Listening on sshd.socket. [ OK ] Reached target Sockets. [ 7.401151] random: crng init done [ 7.404597] random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Reached target Basic System. [ OK ] Started Kernel Logging Service. [ OK ] Started System Logging Service. [ OK ] Started D-Bus System Message Bus. Starting IPv6 Packet Filtering Framework... Starting IPv4 Packet Filtering Framework... Starting Telephony service... [ OK ] Started optee services. Starting PowerVR consumer services... Starting rng-tools.service... [ 7.635066] udc_core: exports duplicate symbol gadget_find_ep_by_name (owned by kernel) Starting Login Service... [ OK ] Started Load/Save Random Seed. [ OK ] Started IPv6 Packet Filtering Framework. [ OK ] Started IPv4 Packet Filtering Framework. [ 7.757020] udc_core: exports duplicate symbol gadget_find_ep_by_name (owned by kernel) [ 7.774423] ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 [ OK ] Started rng-tools.service. [ 7.866362] st-gyro-i2c 16-006b: supply vdd not found, using dummy regulator [ 7.880001] st-gyro-i2c 16-006b: supply vddio not found, using dummy regulator [ 7.899963] st-lsm9ds0-i2c 16-001d: supply vdd not found, using dummy regulator [ OK ] Started Telephony service. [ 7.941452] st-lsm9ds0-i2c 16-001d: supply vddio not found, using dummy regulator [ OK ] Reached target Network (Pre). [ 7.960903] Bluetooth: Core ver 2.22 [ 7.967759] NET: Registered protocol family 31 [ 7.972353] Bluetooth: HCI device and connection manager initialized [ 7.979177] Bluetooth: HCI socket layer initialized [ 7.984243] Bluetooth: L2CAP socket layer initialized [ 7.989422] Bluetooth: SCO socket layer initialized Starting pvrinit.service... Starting Network Service... [ OK ] Started Login Service. [ 8.059242] Bluetooth: HCI UART driver ver 2.3 [ 8.096281] iio iio:device1: registered accelerometer lsm9ds0 [ 8.123929] Bluetooth: HCI UART protocol H4 registered [ OK ] Started Net[ 8.138800] iio iio:device0: registered gyroscope lsm9ds0_gyro work Service[ 8.146629] Bluetooth: HCI UART protocol LL registered . [ 8.162825] Bluetooth: HCI UART protocol Broadcom registered [ 8.173063] Bluetooth: HCI UART protocol QCA registered [ 8.197231] ccree e6601000.crypto: ARM ccree device initialized [ 8.210933] iio iio:device2: registered magnetometer lsm9ds0 [ 8.225886] Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=266) [ OK ] Created slice system-weston.slice. Starting 8.309159] Bluetooth: hci0: change remote baud rate command in firmware 9mSave/Restore Sound Card State... Starting Network Name Resolution... [ 8.443127] rcar_sound ec500000.sound: Can't update kctrl when idle [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Listening on Load/Save RF �citch Status /dev/rfkill Watch. Starting Avahi mDNS/DNS-SD Stack... Starting Permit User Sessions... [ 8.587908] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 8.606449] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 8.613334] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 Starting Target[ 8.624056] cfg80211: failed to load regulatory.db Communication Framework agent... [ OK ] Started PowerVR consumer services. [ OK ] Started pvrinit.service. [ OK ] Started Permit User Sessions. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Target Communication Framework agent. Starting Bluetooth service... [ OK ] Started Getty on tty1. Starting rc.mm.service... [ OK ] Started Serial Getty on ttySC0. [ OK ] Reached target Login Prompts. [ 8.872799] wl18xx_driver wl18xx.6.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2 [ 8.883867] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -2 Starting Load/S[ 8.894697] wlcore: WARNING falling back to default config ave RF Kill Switch Status... [ 8.917314] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 8.922763] Bluetooth: BNEP socket layer initialized [ OK ] Started Load/Save RF Kill Switch Status. [ OK ] Started rc.mm.service. [ OK ] Started Bluetooth service. [ OK ] Reached target Bluetooth. Starting Hostname Service... Starting uim-sysfs.service... [ 9.066947] (stk) : gpio 343 request failed [ 9.066986] kim: probe of kim failed with error -16 [ OK ] Started Hostname Service. [ 9.323198] rcar_sound ec500000.sound: Can't update kctrl when idle [ OK ] Started Save/Restore Sound Card State. [ OK ] Reached target Sound Card. [ 9.392105] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11) [ 9.400771] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead. [ 9.409542] wlcore: WARNING This default nvs file can be removed from the file system [ 9.420759] wlcore: loaded [ OK ] Started uim-sysfs.service. Starting pulseaudio.service... [ OK ] Started pulseaudio.service. [ OK ] Reached target Multi-User System. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Weston Wayland Compositor. [ OK ] Started Update UTMP about System Runlevel Changes. [ 10.630117] audit: type=1006 audit(1622548795.087:2): pid=650 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=1 res=1 Poky (Yocto Project Reference Distro) 3.1.4 h3ulcb ttySC0 h3ulcb login: [ 11.770792] PVR_K: 657: RGX Firmware image 'rgx.fw.4.46.6.62' loaded [ 27.053536] NET: Registered protocol family 38 [ 27.076594] Bluetooth: RFCOMM socket layer initialized [ 27.081805] Bluetooth: RFCOMM ver 1.11 [ 35.807182] snd-3.3v: disabling [ 35.810348] snd-vcc5v: disabling [ 35.813639] SDHI0 Vcc: disabling [ 35.816945] wlan-en-regulator: disabling [ 35.820998] SDHI0 VccQ: disabling h3ulcb login: root Last login: Tue Jun 1 11:59:55 UTC 2021 root@h3ulcb:~# root@h3ulcb:~# root@h3ulcb:~# cat /sys/class/drm/card0-HDMI-A-2/modes 1920x1080 1920x1080 1920x1080 1920x1080 1920x1080i 1920x1080i 1920x1080i 1920x1080i 1920x1080i 1680x1050 1280x1024 1440x900 1280x800 1280x720 1280x720 1280x720 1280x720 1280x720 1024x768 800x600 720x576 720x576 720x480 720x480 640x480 640x480 root@h3ulcb:~#
By the way, looking at your log, it seems that the panel is different.
OK case : Manufacturer: BQQ Model 3239 Serial Number 808548400
NG case : Manufacturer: BQX Model 3030 Serial Number 808466040
What if you use "BQQ Model 3239" in EVB1 HDMI-A-2 environment?
Hi Gohda,
Thanks for your help. I exchange the panels to different HDMI port, but the resolution is still the same.
All of the firmware is installed by this manual: https://elinux.org/R-Car/Boards/H3SK#Flashing_firmware
I install the same firmware for the 2 starter kit.
The log of mine are are too large, is there any keyword for me to compare?
I'll try the v5.5.0 version firmware to check again.
Sharon
Could you attach the all boot log of H3 SK(S/N 2748)?
NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.3.0.1NOTICE: BL2: PRR is R-Car H3 Ver.2.0NOTICE: BL2: Board is Starter Kit Premier Rev.1.0NOTICE: BL2: Boot device is HyperFlash(80MHz)NOTICE: BL2: LCM state is CMNOTICE: AVS setting succeeded. DVFS_SetVID=0x53NOTICE: BL2: DDR3200(rev.0.41)NOTICE: BL2: [COLD_BOOT]NOTICE: BL2: DRAM Split is 4chNOTICE: BL2: QoS is default setting(rev.0.21)NOTICE: BL2: DRAM refresh interval 1.95 usecNOTICE: BL2: Periodic Write DQ TrainingNOTICE: BL2: CH0: 400000000 - 43fffffff, 1 GiBNOTICE: BL2: CH1: 500000000 - 53fffffff, 1 GiBNOTICE: BL2: CH2: 600000000 - 63fffffff, 1 GiBNOTICE: BL2: CH3: 700000000 - 73fffffff, 1 GiBNOTICE: BL2: Lossy Decomp areasNOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0NOTICE: BL2: FDT at 0xe63267c8NOTICE: BL2: v2.3():7638cfb-dirtyNOTICE: BL2: Built : 03:46:00, Sep 23 2021NOTICE: BL2: Normal bootNOTICE: BL2: dst=0xe6326300 src=0x8180000 len=512(0x200)NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)NOTICE: rcar_file_len: len: 0x0003e000NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=253952(0x3e000)NOTICE: rcar_file_len: len: 0x00200000NOTICE: BL2: dst=0x44100000 src=0x8200000 len=2097152(0x200000)NOTICE: rcar_file_len: len: 0x00100000NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)NOTICE: BL2: Booting BL31
U-Boot 2020.10 (Sep 23 2021 - 03:43:16 +0000)
CPU: Renesas Electronics R8A7795 rev 2.0Model: Renesas H3ULCB board based on r8a77950DRAM: 3.9 GiBFlash: 64 MiBMMC: sd@ee100000: 0, sd@ee140000: 1Loading Environment from MMC... OKIn: serial@e6e88000Out: serial@e6e88000Err: serial@e6e88000Net: eth0: ethernet@e6800000Hit any key to stop autoboot: 024173056 bytes read in 265 ms (87 MiB/s)122125 bytes read in 4 ms (29.1 MiB/s)Moving Image from 0x48080000 to 0x48200000, end=49990000## Flattened Device Tree blob at 48000000 Booting using the fdt blob at 0x48000000 Using Device Tree in place at 0000000048000000, end 0000000048020d0cOverlap found: 0x500000000..0x53fffffff / 0x500000000..0x53fffffffOverlap found: 0x600000000..0x63fffffff / 0x600000000..0x63fffffffOverlap found: 0x700000000..0x73fffffff / 0x700000000..0x73fffffff
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd073][ 0.000000] Linux version 5.10.0-yocto-standard (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 9.3.0, GNU ld (GNU Binutils) 2.34.0.20200220) #1 SMP PREEMPT Tue Nov 23 15:25:38 UTC 2021[ 0.000000] Machine model: Renesas H3ULCB Kingfisher board based on r8a77951[ 0.000000] efi: UEFI not found.[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB[ 0.000000] OF: reserved mem: initialized node linux,cma@57000000, compatible id shared-dma-pool[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB[ 0.000000] OF: reserved mem: initialized node linux,multimedia@70000000, compatible id shared-dma-pool[ 0.000000] NUMA: No NUMA configuration found[ 0.000000] NUMA: Faking a node at [mem 0x0000000048000000-0x000000073fffffff][ 0.000000] NUMA: NODE_DATA [mem 0x73f7c2b00-0x73f7c4fff][ 0.000000] Zone ranges:[ 0.000000] DMA [mem 0x0000000048000000-0x000000007fffffff][ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff][ 0.000000] Normal [mem 0x0000000100000000-0x000000073fffffff][ 0.000000] Movable zone start for each node[ 0.000000] Early memory node ranges[ 0.000000] node 0: [mem 0x0000000048000000-0x0000000053ffffff][ 0.000000] node 0: [mem 0x0000000057000000-0x000000007fffffff][ 0.000000] node 0: [mem 0x0000000500000000-0x000000053fffffff][ 0.000000] node 0: [mem 0x0000000600000000-0x000000063fffffff][ 0.000000] node 0: [mem 0x0000000700000000-0x000000073fffffff][ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000073fffffff][ 0.000000] psci: probing for conduit method from DT.[ 0.000000] psci: PSCIv1.1 detected in firmware.[ 0.000000] psci: Using standard PSCI v0.2 function IDs[ 0.000000] psci: Trusted OS resident on physical CPU 0x0[ 0.000000] psci: SMC Calling Convention v1.2[ 0.000000] percpu: Embedded 23 pages/cpu s55512 r8192 d30504 u94208[ 0.000000] Detected PIPT I-cache on CPU0[ 0.000000] CPU features: detected: EL2 vector hardening[ 0.000000] CPU features: detected: Spectre-v2[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 987648[ 0.000000] Policy zone: Normal[ 0.000000] Kernel command line: rw root=/dev/mmcblk1p1 rootwait[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off[ 0.000000] software IO TLB: mapped [mem 0x0000000050000000-0x0000000054000000] (64MB)[ 0.000000] Memory: 3171308K/4014080K available (13568K kernel code, 1270K rwdata, 5784K rodata, 2880K init, 494K bss, 171028K reserved, 671744K cma-reserved)[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1[ 0.000000] rcu: Preemptible hierarchical RCU implementation.[ 0.000000] rcu: RCU event tracing is enabled.[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.[ 0.000000] Trampoline variant of Tasks RCU enabled.[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0[ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x4ec with crng_init=0[ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt).[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns[ 0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns[ 0.000154] Console: colour dummy device 80x25[ 0.000344] printk: console [tty0] enabled[ 0.000414] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)[ 0.000429] pid_max: default: 32768 minimum: 301[ 0.000490] LSM: Security Framework initializing[ 0.000555] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)[ 0.000584] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)[ 0.001956] rcu: Hierarchical SRCU implementation.[ 0.003019] Detected Renesas R-Car Gen3 r8a7795 ES2.0[ 0.004076] EFI services will not be available.[ 0.004394] smp: Bringing up secondary CPUs ...[ 0.004805] Detected PIPT I-cache on CPU1[ 0.004853] CPU1: Booted secondary processor 0x0000000001 [0x411fd073][ 0.005293] Detected PIPT I-cache on CPU2[ 0.005317] CPU2: Booted secondary processor 0x0000000002 [0x411fd073][ 0.005724] Detected PIPT I-cache on CPU3[ 0.005746] CPU3: Booted secondary processor 0x0000000003 [0x411fd073][ 0.006130] CPU features: detected: ARM erratum 845719[ 0.006142] Detected VIPT I-cache on CPU4[ 0.006189] CPU4: Booted secondary processor 0x0000000100 [0x410fd034][ 0.006636] Detected VIPT I-cache on CPU5[ 0.006663] CPU5: Booted secondary processor 0x0000000101 [0x410fd034][ 0.007071] Detected VIPT I-cache on CPU6[ 0.007097] CPU6: Booted secondary processor 0x0000000102 [0x410fd034][ 0.007502] Detected VIPT I-cache on CPU7[ 0.007528] CPU7: Booted secondary processor 0x0000000103 [0x410fd034][ 0.007606] smp: Brought up 1 node, 8 CPUs[ 0.007668] SMP: Total of 8 processors activated.[ 0.007676] CPU features: detected: 32-bit EL0 Support[ 0.007683] CPU features: detected: CRC32 instructions[ 0.007691] CPU features: detected: 32-bit EL1 Support[ 0.020695] CPU: All CPU(s) started at EL1[ 0.020734] alternatives: patching kernel code[ 0.021786] devtmpfs: initialized[ 0.030286] KASLR disabled due to lack of seed[ 0.030619] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns[ 0.030642] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)[ 0.038883] pinctrl core: initialized pinctrl subsystem[ 0.039381] DMI not present or invalid.[ 0.039735] NET: Registered protocol family 16[ 0.040658] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations[ 0.040750] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations[ 0.040847] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations[ 0.040888] audit: initializing netlink subsys (disabled)[ 0.041040] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1[ 0.041359] thermal_sys: Registered thermal governor 'power_allocator'[ 0.042259] cpuidle: using governor menu[ 0.042406] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.[ 0.042530] ASID allocator initialised with 65536 entries[ 0.042702] Serial: AMBA PL011 UART driver[ 0.076733] sh-pfc e6060000.pinctrl: r8a77951_pfc support registered[ 0.085067] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages[ 0.085080] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages[ 0.085088] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages[ 0.085096] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages[ 0.086023] cryptd: max_cpu_qlen set to 1000[ 0.087965] ACPI: Interpreter disabled.[ 0.092059] iommu: Default domain type: Translated[ 0.092805] ipmmu-vmsa e67b0000.mmu: IPMMU context 0 is reserved[ 0.093679] vgaarb: loaded[ 0.093893] SCSI subsystem initialized[ 0.094146] usbcore: registered new interface driver usbfs[ 0.094172] usbcore: registered new interface driver hub[ 0.094215] usbcore: registered new device driver usb[ 0.096510] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz[ 0.097032] mc: Linux media interface: v0.10[ 0.097054] videodev: Linux video capture interface: v2.00[ 0.097100] pps_core: LinuxPPS API ver. 1 registered[ 0.097107] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>[ 0.097122] PTP clock support registered[ 0.097323] EDAC MC: Ver: 3.0.0[ 0.098319] FPGA manager framework[ 0.098392] Advanced Linux Sound Architecture Driver Initialized.[ 0.098927] clocksource: Switched to clocksource arch_sys_counter[ 0.099072] VFS: Disk quotas dquot_6.6.0[ 0.099117] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)[ 0.099238] pnp: PnP ACPI: disabled[ 0.102699] NET: Registered protocol family 2[ 0.103017] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)[ 0.103062] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)[ 0.103209] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)[ 0.103499] TCP: Hash tables configured (established 32768 bind 32768)[ 0.103607] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)[ 0.103670] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)[ 0.103824] NET: Registered protocol family 1[ 0.104221] RPC: Registered named UNIX socket transport module.[ 0.104232] RPC: Registered udp transport module.[ 0.104238] RPC: Registered tcp transport module.[ 0.104244] RPC: Registered tcp NFSv4.1 backchannel transport module.[ 0.104257] PCI: CLS 0 bytes, default 64[ 0.105073] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available[ 0.105367] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available[ 0.105926] kvm [1]: HYP mode not available[ 0.108729] Initialise system trusted keyrings[ 0.108838] workingset: timestamp_bits=42 max_order=20 bucket_order=0[ 0.111852] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.112279] NFS: Registering the id_resolver key type[ 0.112301] Key type id_resolver registered[ 0.112307] Key type id_legacy registered[ 0.112362] nfs4filelayout_init: NFSv4 File Layout Driver Registering...[ 0.112456] 9p: Installing v9fs 9p2000 file system support[ 0.137694] Key type asymmetric registered[ 0.137707] Asymmetric key parser 'x509' registered[ 0.137736] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)[ 0.137746] io scheduler mq-deadline registered[ 0.137753] io scheduler kyber registered[ 0.142439] gpio_rcar e6050000.gpio: driving 16 GPIOs[ 0.142751] gpio_rcar e6051000.gpio: driving 29 GPIOs[ 0.142948] gpio-455 (BL PWM 100%): hogged as output/high[ 0.143082] gpio_rcar e6052000.gpio: driving 15 GPIOs[ 0.143367] gpio_rcar e6053000.gpio: driving 16 GPIOs[ 0.143531] gpio-432 (MOST RST): hogged as output/high[ 0.143655] gpio_rcar e6054000.gpio: driving 18 GPIOs[ 0.143931] gpio_rcar e6055000.gpio: driving 26 GPIOs[ 0.144096] gpio-381 (Onboard MCh Audio): hogged as output/high[ 0.144216] gpio_rcar e6055400.gpio: driving 32 GPIOs[ 0.144489] gpio_rcar e6055800.gpio: driving 4 GPIOs[ 0.145691] rcar-pcie fe000000.pcie: host bridge /soc/pcie@fe000000 ranges:[ 0.145718] rcar-pcie fe000000.pcie: IO 0x00fe100000..0x00fe1fffff -> 0x0000000000[ 0.145741] rcar-pcie fe000000.pcie: MEM 0x00fe200000..0x00fe3fffff -> 0x00fe200000[ 0.145761] rcar-pcie fe000000.pcie: MEM 0x0030000000..0x0037ffffff -> 0x0030000000[ 0.145775] rcar-pcie fe000000.pcie: MEM 0x0038000000..0x003fffffff -> 0x0038000000[ 0.145792] rcar-pcie fe000000.pcie: IB MEM 0x0040000000..0x007fffffff -> 0x0040000000[ 0.145837] rcar-pcie fe000000.pcie: no pcie3v3 regulator found[ 0.145848] rcar-pcie fe000000.pcie: no pcie1v8 regulator found[ 0.210558] rcar-pcie fe000000.pcie: PCIe link down[ 0.210729] rcar-pcie ee800000.pcie: host bridge /soc/pcie@ee800000 ranges:[ 0.210753] rcar-pcie ee800000.pcie: IO 0x00ee900000..0x00ee9fffff -> 0x0000000000[ 0.210772] rcar-pcie ee800000.pcie: MEM 0x00eea00000..0x00eebfffff -> 0x00eea00000[ 0.210791] rcar-pcie ee800000.pcie: MEM 0x00c0000000..0x00c7ffffff -> 0x00c0000000[ 0.210804] rcar-pcie ee800000.pcie: MEM 0x00c8000000..0x00cfffffff -> 0x00c8000000[ 0.210821] rcar-pcie ee800000.pcie: IB MEM 0x0040000000..0x007fffffff -> 0x0040000000[ 0.212473] EINJ: ACPI disabled.[ 0.230369] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled[ 0.231740] SuperH (H)SCI(F) driver initialized[ 0.232084] e6540000.serial: ttySC1 at MMIO 0xe6540000 (irq = 42, base_baud = 0) is a hscif[ 0.232241] serial serial0: tty port ttySC1 registered[ 0.232710] e6550000.serial: ttySC3 at MMIO 0xe6550000 (irq = 43, base_baud = 0) is a hscif[ 0.233276] e6e68000.serial: ttySC2 at MMIO 0xe6e68000 (irq = 130, base_baud = 0) is a scif[ 0.233781] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 131, base_baud = 0) is a scif[ 1.381045] printk: console [ttySC0] enabled[ 1.391121] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)[ 1.401012] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver[ 1.416472] loop: module loaded[ 1.420453] megasas: 07.714.04.00-rc1[ 1.426671] renesas-rpc ee200000.rpc0: using DMA read (dma0chan0)[ 1.433793] 10 fixed-partitions partitions found on MTD device HyperFlash[ 1.440611] Creating 10 MTD partitions on "HyperFlash":[ 1.445846] 0x000000000000-0x000000040000 : "bootparam"[ 1.455535] 0x000000040000-0x000000180000 : "bl2"[ 1.463416] 0x000000180000-0x0000001c0000 : "cert_header_sa6"[ 1.471437] 0x0000001c0000-0x000000200000 : "bl31"[ 1.479415] 0x000000200000-0x000000640000 : "tee"[ 1.487405] 0x000000640000-0x000000700000 : "uboot"[ 1.495405] 0x000000700000-0x000000740000 : "uboot-env"[ 1.503417] 0x000000740000-0x0000007c0000 : "dtb"[ 1.511411] 0x0000007c0000-0x000001bc0000 : "kernel"[ 1.519426] 0x000001bc0000-0x000004000000 : "user"[ 1.527425] renesas-rpc-hyperflash renesas-rpc-hyperflash: probed flash id:7e0001[ 1.536533] libphy: Fixed MDIO Bus: probed[ 1.541306] tun: Universal TUN/TAP device driver, 1.6[ 1.546478] CAN device driver interface[ 1.550930] rcar_can e6c30000.can: device registered (IRQ128)[ 1.557157] rcar_can e6c38000.can: device registered (IRQ129)[ 1.563475] usbcore: registered new interface driver peak_usb[ 1.569648] thunder_xcv, ver 1.0[ 1.572927] thunder_bgx, ver 1.0[ 1.576180] nicpf, ver 1.0[ 1.579412] hclge is initializing[ 1.582757] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version[ 1.589989] hns3: Copyright (c) 2017 Huawei Corporation.[ 1.595336] e1000: Intel(R) PRO/1000 Network Driver[ 1.600217] e1000: Copyright (c) 1999-2006 Intel Corporation.[ 1.605984] e1000e: Intel(R) PRO/1000 Network Driver[ 1.610950] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.[ 1.616895] igb: Intel(R) Gigabit Ethernet Network Driver[ 1.622296] igb: Copyright (c) 2007-2014 Intel Corporation.[ 1.627885] igbvf: Intel(R) Gigabit Virtual Function Network Driver[ 1.634153] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.[ 1.640088] sky2: driver version 1.30[ 1.644911] libphy: ravb_mii: probed[ 1.651143] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:09:0a:02:f3:22, IRQ 125.[ 1.660714] VFIO - User Level meta-driver version: 0.3[ 1.667075] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver[ 1.673614] ehci-pci: EHCI PCI platform driver[ 1.678090] ehci-platform: EHCI generic platform driver[ 1.710979] ehci-platform ee080100.usb: EHCI Host Controller[ 1.716658] ehci-platform ee080100.usb: new USB bus registered, assigned bus number 1[ 1.724542] ehci-platform ee080100.usb: irq 174, io mem 0xee080100[ 1.742931] ehci-platform ee080100.usb: USB 2.0 started, EHCI 1.10[ 1.749476] hub 1-0:1.0: USB hub found[ 1.753248] hub 1-0:1.0: 1 port detected[ 1.757612] ehci-platform ee0a0100.usb: EHCI Host Controller[ 1.763302] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 2[ 1.771202] ehci-platform ee0a0100.usb: irq 175, io mem 0xee0a0100[ 1.790932] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10[ 1.797374] hub 2-0:1.0: USB hub found[ 1.801144] hub 2-0:1.0: 1 port detected[ 1.805454] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver[ 1.811668] ohci-pci: OHCI PCI platform driver[ 1.816154] ohci-platform: OHCI generic platform driver[ 1.821621] ohci-platform ee080000.usb: Generic Platform OHCI controller[ 1.828338] ohci-platform ee080000.usb: new USB bus registered, assigned bus number 3[ 1.836215] ohci-platform ee080000.usb: irq 174, io mem 0xee080000[ 1.929907] hub 3-0:1.0: USB hub found[ 1.933678] hub 3-0:1.0: 1 port detected[ 1.937957] ohci-platform ee0a0000.usb: Generic Platform OHCI controller[ 1.944690] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 4[ 1.952569] ohci-platform ee0a0000.usb: irq 175, io mem 0xee0a0000[ 2.045898] hub 4-0:1.0: USB hub found[ 2.049666] hub 4-0:1.0: 1 port detected[ 2.054293] xhci-hcd ee000000.usb: xHCI Host Controller[ 2.059552] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 5[ 2.082829] xhci-hcd ee000000.usb: hcc params 0x014051ce hci version 0x100 quirks 0x0000000000830410[ 2.091991] xhci-hcd ee000000.usb: irq 173, io mem 0xee000000[ 2.098108] hub 5-0:1.0: USB hub found[ 2.101880] hub 5-0:1.0: 1 port detected[ 2.105949] xhci-hcd ee000000.usb: xHCI Host Controller[ 2.111185] xhci-hcd ee000000.usb: new USB bus registered, assigned bus number 6[ 2.118590] xhci-hcd ee000000.usb: Host supports USB 3.0 SuperSpeed[ 2.124900] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.[ 2.133241] hub 6-0:1.0: USB hub found[ 2.137010] hub 6-0:1.0: 1 port detected[ 2.141452] usbcore: registered new interface driver usb-storage[ 2.148919] renesas_usbhs e6590000.usb: host probed[ 2.153814] renesas_usbhs e6590000.usb: no transceiver found[ 2.159554] renesas_usbhs e6590000.usb: gadget probed[ 2.164764] renesas_usbhs e6590000.usb: probed[ 2.170339] i2c /dev entries driver[ 2.183901] cs2000-cp 2-004f: revision - C1[ 2.189017] pca953x 2-0074: supply vcc not found, using dummy regulator[ 2.195708] pca953x 2-0074: using no AI[ 2.201576] gpio-340 (Audio_Out_OFF): hogged as output/high[ 2.207832] gpio-346 (HUB pwen): hogged as output/high[ 2.213653] gpio-347 (HUB rst): hogged as output/high[ 2.220265] gpio-349 (OTG EXTLPn): hogged as output/high[ 2.226259] gpio-348 (OTG OFFVBUSn): hogged as output/low[ 2.232339] gpio-355 (SND_RST): hogged as output/high[ 2.238012] pca953x 2-0075: supply vcc not found, using dummy regulator[ 2.244685] pca953x 2-0075: using no AI[ 2.251645] gpio-330 (GPS rst): hogged as output/high[ 2.257821] gpio-333 (FPDLink shdn): hogged as output/high[ 2.263506] i2c-rcar e6510000.i2c: probed[ 2.270595] random: fast init done[ 2.278244] pca953x 4-0076: supply vcc not found, using dummy regulator[ 2.284952] pca953x 4-0076: using no AI[ 2.289990] gpio-308 (Video-B A0): hogged as output/low[ 2.295485] gpio-309 (Video-B A1): hogged as output/high[ 2.301056] gpio-310 (Video-A A0): hogged as output/low[ 2.306541] gpio-311 (Video-A A1): hogged as output/high[ 2.312265] gpio-318 (RaspB_IO1): hogged as output/high[ 2.317749] gpio-319 (RaspB_IO0): hogged as output/high[ 2.323235] gpio-312 (SAM RST): hogged as output/high[ 2.328546] gpio-313 (SAM PWR): hogged as output/low[ 2.333770] gpio-322 (LVDS switch): hogged as output/high[ 2.339492] pca953x 4-0077: supply vcc not found, using dummy regulator[ 2.346170] pca953x 4-0077: using no AI[ 2.350759] gpio-292 (mPCIe WAKE#): hogged as output/low[ 2.356342] gpio-293 (mPCIe W_DISABLE): hogged as output/high[ 2.362226] gpio-294 (mPCIe CLKREQ#): hogged as input[ 2.367412] gpio-295 (mPCIe OVC): hogged as input[ 2.372410] i2c-rcar e66d8000.i2c: probed[ 2.377801] i2c i2c-2: Added multiplexed i2c bus 9[ 2.382717] i2c i2c-2: Added multiplexed i2c bus 10[ 2.387744] i2c i2c-2: Added multiplexed i2c bus 11[ 2.392745] i2c i2c-2: Added multiplexed i2c bus 12[ 2.397929] adv7511 13-003d: supply avdd not found, using dummy regulator[ 2.404790] adv7511 13-003d: supply dvdd not found, using dummy regulator[ 2.411610] adv7511 13-003d: supply pvdd not found, using dummy regulator[ 2.418435] adv7511 13-003d: supply bgvdd not found, using dummy regulator[ 2.425357] adv7511 13-003d: supply dvdd-3v not found, using dummy regulator[ 2.455847] i2c i2c-2: Added multiplexed i2c bus 13[ 2.460866] i2c i2c-2: Added multiplexed i2c bus 14[ 2.466039] i2c i2c-2: Added multiplexed i2c bus 15[ 2.466231] edt_ft5x06 15-0038: supply vcc not found, using dummy regulator[ 2.471412] i2c i2c-2: Added multiplexed i2c bus 16[ 2.478750] edt_ft5x06 15-0038: touchscreen probe failed[ 2.482790] pca954x 2-0071: registered 8 multiplexed busses for I2C switch pca9548[ 2.483274] i2c i2c-4: Added multiplexed i2c bus 17[ 2.501005] i2c i2c-4: Added multiplexed i2c bus 18[ 2.506001] i2c i2c-4: Added multiplexed i2c bus 19[ 2.511023] i2c i2c-4: Added multiplexed i2c bus 20[ 2.516216] i2c i2c-4: Added multiplexed i2c bus 21[ 2.521440] i2c i2c-4: Added multiplexed i2c bus 22[ 2.526432] i2c i2c-4: Added multiplexed i2c bus 23[ 2.531892] dummy 24-006c: failed reading[ 2.535997] i2c i2c-4: Added multiplexed i2c bus 24[ 2.540882] pca954x 4-0071: registered 8 multiplexed busses for I2C switch pca9548[ 2.715313] usb 6-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd[ 2.744833] hub 6-1:1.0: USB hub found[ 2.748889] hub 6-1:1.0: 4 ports detected[ 2.760734] ov5642 22-003c: reg_write: i2c write error, reg: 3103[ 2.771152] rcar-csi2 fea80000.csi2: 2 lanes found[ 2.776252] rcar-csi2 feaa0000.csi2: 4 lanes found[ 2.785485] rcar-vin e6ef0000.video: Device registered as video0[ 2.791583] rcar-vin e6ef1000.video: Device registered as video1[ 2.797653] rcar-vin e6ef2000.video: Device registered as video2[ 2.803744] rcar-vin e6ef3000.video: Device registered as video3[ 2.809816] rcar-vin e6ef4000.video: Device registered as video4[ 2.815905] rcar-vin e6ef5000.video: Device registered as video5[ 2.823914] rcar_gen3_thermal e6198000.thermal: is using pseudo fixed FUSE values[ 2.835680] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points[ 2.847039] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points[ 2.858227] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points[ 2.867651] sdhci: Secure Digital Host Controller Interface driver[ 2.873841] sdhci: Copyright(c) Pierre Ossman[ 2.878832] Synopsys Designware Multimedia Card Interface Driver[ 2.879363] renesas_sdhi_internal_dmac ee100000.mmc: Got CD GPIO[ 2.885515] sdhci-pltfm: SDHCI platform and OF driver helper[ 2.894950] usb 5-1: new high-speed USB device number 2 using xhci-hcd[ 2.903998] ledtrig-cpu: registered to indicate activity on CPUs[ 2.910306] SMCCC: SOC_ID: ARCH_FEATURES(ARCH_SOC_ID) returned error: fffffffffffffffd[ 2.918561] usbcore: registered new interface driver usbhid[ 2.924136] usbhid: USB HID core driver[ 2.929229] optee: probing for conduit method.[ 2.929797] renesas_sdhi_internal_dmac ee140000.mmc: mmc0 base at 0x00000000ee140000, max clock rate 200 MHz[ 2.933696] optee: revision 3.8 (43a5c578)[ 2.944124] optee driver R-Car Rev.1.0.11[ 2.952717] optee: initialized driver[ 2.969090] rcar_sound ec500000.sound: probed[ 2.974098] NET: Registered protocol family 17[ 2.978560] can: controller area network core[ 2.982991] NET: Registered protocol family 29[ 2.987440] can: raw protocol[ 2.990404] can: broadcast manager protocol[ 2.994607] can: netlink gateway - max_hops=1[ 2.999112] 9pnet: Installing 9P2000 support[ 3.003426] Key type dns_resolver registered[ 3.008092] registered taskstats version 1[ 3.012199] Loading compiled-in X.509 certificates[ 3.026742] thermal emergency: set temperature to 110 celsius[ 3.032713] thermal emergency: shutdown target cpus 1-7[ 3.035569] mmc0: new HS400 MMC card at address 0001[ 3.037941] thermal emergency: freq scaled target cpus 0[ 3.043642] mmcblk0: mmc0:0001 8GSD4R 7.28 GiB[ 3.048497] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs[ 3.052894] mmcblk0boot0: mmc0:0001 8GSD4R partition 1 31.9 MiB[ 3.064738] hub 5-1:1.0: USB hub found[ 3.065362] mmcblk0boot1: mmc0:0001 8GSD4R partition 2 31.9 MiB[ 3.065393] rcar-pcie ee800000.pcie: host bridge /soc/pcie@ee800000 ranges:[ 3.065412] rcar-pcie ee800000.pcie: IO 0x00ee900000..0x00ee9fffff -> 0x0000000000[ 3.065427] rcar-pcie ee800000.pcie: MEM 0x00eea00000..0x00eebfffff -> 0x00eea00000[ 3.065439] rcar-pcie ee800000.pcie: MEM 0x00c0000000..0x00c7ffffff -> 0x00c0000000[ 3.065447] rcar-pcie ee800000.pcie: MEM 0x00c8000000..0x00cfffffff -> 0x00c8000000[ 3.065460] rcar-pcie ee800000.pcie: IB MEM 0x0040000000..0x007fffffff -> 0x0040000000[ 3.069390] hub 5-1:1.0: 4 ports detected[ 3.075202] mmcblk0rpmb: mmc0:0001 8GSD4R partition 3 512 KiB, chardev (236:0)[ 3.144680] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18[ 3.342561] rcar-pcie ee800000.pcie: PCIe link down[ 3.358694] cpu cpu0: EM: created perf domain[ 3.363629] cpu cpu4: EM: created perf domain[ 3.369303] Failed to set up IOMMU for device ee160000.mmc; retaining platform DMA ops[ 3.369601] Failed to set up IOMMU for device ee100000.mmc; retaining platform DMA ops[ 3.385300] renesas_sdhi_internal_dmac ee100000.mmc: Got CD GPIO[ 3.389206] asoc-audio-graph-card sound@0: ASoC: no DMI vendor name![ 3.400508] asoc-audio-graph-card sound@1: ASoC: no DMI vendor name![ 3.407840] asoc-audio-graph-card sound@2: ASoC: no DMI vendor name![ 3.415022] asoc-audio-graph-card sound@3: ASoC: no DMI vendor name![ 3.424607] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0[ 3.432372] [drm] Device feb00000.display probed[ 3.440146] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz[ 3.493017] Console: switching to colour frame buffer device 128x48[ 3.505184] renesas_sdhi_internal_dmac ee160000.mmc: mmc2 base at 0x00000000ee160000, max clock rate 50 MHz[ 3.515688] renesas_sdhi_internal_dmac ee160000.mmc: card claims to support voltages below defined range[ 3.519710] rcar-du feb00000.display: [drm] fb0: rcar-dudrmfb frame buffer device[ 3.550480] input: keyboard as /devices/platform/keyboard/input/input1[ 3.559095] ALSA device list:[ 3.562114] #0: ak4613[ 3.564699] #1: pcm3168a[ 3.567497] #2: radio[ 3.569989] #3: wl18xx[ 3.572808] md: Waiting for all devices to be available before autodetect[ 3.579699] md: If you don't use raid, use raid=noautodetect[ 3.585440] md: Autodetecting RAID arrays.[ 3.589599] md: autorun ...[ 3.592438] md: ... autorun DONE.[ 3.595904] Waiting for root device /dev/mmcblk1p1...[ 3.608646] mmc2: new high speed SDIO card at address 0001[ 3.752502] mmc1: new ultra high speed SDR104 SDXC card at address 59b4[ 3.760242] mmcblk1: mmc1:59b4 USD00 118 GiB[ 3.774643] mmcblk1: p1[ 3.792214] EXT4-fs (mmcblk1p1): mounting ext3 file system using the ext4 subsystem[ 4.285869] EXT4-fs (mmcblk1p1): recovery complete[ 4.297008] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)[ 4.310314] VFS: Mounted root (ext3 filesystem) on device 179:97.[ 4.337308] devtmpfs: mounted[ 4.346982] Freeing unused kernel memory: 2880K[ 4.356727] Run /sbin/init as init process[ 4.601757] systemd[1]: System time before build time, advancing clock.[ 4.681910] NET: Registered protocol family 10[ 4.692955] Segment Routing with IPv6[ 4.739877] systemd[1]: systemd 244.3+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)[ 4.770612] systemd[1]: Detected architecture arm64.
Welcome to Poky (Yocto Project Reference Distro) 3.1.4 (dunfell)!
[ 4.819922] systemd[1]: Set hostname to <h3ulcb>.[ 5.221896] random: systemd: uninitialized urandom read (16 bytes read)[ 5.232493] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.[ 5.252446] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)[ 5.266980] systemd[1]: Created slice system-getty.slice.[ OK ] Created slice system-getty.slice.[ 5.291067] random: systemd: uninitialized urandom read (16 bytes read)[ 5.301215] systemd[1]: Created slice system-serial\x2dgetty.slice.[ OK ] Created slice system-serial\x2dgetty.slice.[ 5.327038] random: systemd: uninitialized urandom read (16 bytes read)[ 5.337179] systemd[1]: Created slice User and Session Slice.[ OK ] Created slice User and Session Slice.[ 5.359209] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.[ OK ] Started Dispatch Password …ts to Console Directory Watch.[ 5.387152] systemd[1]: Started Forward Password Requests to Wall Directory Watch.[ OK ] Started Forward Password R…uests to Wall Directory Watch.[ 5.415099] systemd[1]: Reached target Paths.[ OK ] Reached target Paths.[ 5.435190] systemd[1]: Reached target Remote File Systems.[ OK ] Reached target Remote File Systems.[ 5.459098] systemd[1]: Reached target Slices.[ OK ] Reached target Slices.[ 5.483139] systemd[1]: Reached target Swap.[ OK ] Reached target Swap.[ 5.509469] systemd[1]: Listening on RPCbind Server Activation Socket.[ OK ] Listening on RPCbind Server Activation Socket.[ 5.539162] systemd[1]: Reached target RPC Port Mapper.[ OK ] Reached target RPC Port Mapper.[ 5.569243] systemd[1]: Listening on Syslog Socket.[ OK ] Listening on Syslog Socket.[ 5.595473] systemd[1]: Listening on initctl Compatibility Named Pipe.[ OK ] Listening on initctl Compatibility Named Pipe.[ 5.623976] systemd[1]: Listening on Journal Audit Socket.[ OK ] Listening on Journal Audit Socket.[ 5.651581] systemd[1]: Listening on Journal Socket (/dev/log).[ OK ] Listening on Journal Socket (/dev/log).[ 5.679726] systemd[1]: Listening on Journal Socket.[ OK ] Listening on Journal Socket.[ 5.704009] systemd[1]: Listening on Network Service Netlink Socket.[ OK ] Listening on Network Service Netlink Socket.[ 5.731709] systemd[1]: Listening on udev Control Socket.[ OK ] Listening on udev Control Socket.[ 5.759444] systemd[1]: Listening on udev Kernel Socket.[ OK ] Listening on udev Kernel Socket.[ 5.792233] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System...[ 5.823924] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System...[ 5.856163] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System...[ 5.888742] systemd[1]: Mounting Temporary Directory (/tmp)... Mounting Temporary Directory (/tmp)...[ 5.920342] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel...[ 5.955868] systemd[1]: Starting Start psplash boot splash screen... Starting Start psplash boot splash screen...[ 5.993613] systemd[1]: Started Hardware RNG Entropy Gatherer Daemon.[ OK ] Started Hardware RNG Entropy Gatherer Daemon.[ 6.027548] systemd[1]: Starting RPC Bind... Starting RPC Bind...[ 6.047257] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.[ 6.061933] systemd[1]: Starting Journal Service... Starting Journal Service...[ 6.090084] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules...[ 6.108028] mmngr: loading out-of-tree module taints kernel.[ 6.116032] rgnmm_drv mmngr: assigned reserved memory node linux,multimedia@70000000[ 6.118890] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems...[ 6.140839] EXT4-fs (mmcblk1p1): re-mounted. Opts: (null)[ 6.155186] systemd[1]: Starting udev Coldplug all Devices... Starting udev Coldplug all Devices...[ 6.185195] systemd[1]: Started Start psplash boot splash screen.[ OK ] Started Start psplash boot splash screen.[ 6.211858] systemd[1]: Started RPC Bind.[ OK ] Started RPC Bind.[ 6.236120] systemd[1]: Started Journal Service.[ OK ] Started Journal Service.[ OK ] Mounted Huge Pages File System.[ OK ] Mounted POSIX Message Queue [ 6.280498] PVR_K: 316: Read BVNC 4.46.6.62 from HW device registersFile System.[ 6.287998] PVR_K: 316: RGX Device registered with BVNC 4.46.6.62
[ 6.296358] [drm] Initialized pvr 1.11.5516664 20170530 for fd000000.gsx on minor 1[ OK ] Mounted Kernel Debug File System.[ OK ] Mounted Temporary Directory (/tmp).[ OK ] Started Create list of sta… nodes for the current kernel.[ OK ] Started Remount Root and Kernel File Systems.[ OK ] Started Load Kernel Modules. Mounting Kernel Configuration File System...[ OK ] Started Start psplash-syst…progress communication helper. Starting Flush Journal to Persistent Storage...[ 6.478686] systemd-journald[312]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create Static Device Nodes in /dev...[ OK ] Mounted Kernel Configuration File System.[ OK ] Started Flush Journal to Persistent Storage.[ OK ] Started Apply Kernel Variables.[ OK ] Started Create Static Device Nodes in /dev.[ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... Starting udev Kernel Device Manager...[ OK ] Mounted /var/volatile. Starting Load/Save Random Seed...[ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories...[ OK ] Started udev Coldplug all Devices.[ 6.848810] random: crng init done[ 6.852219] random: 7 urandom warning(s) missed due to ratelimiting[ OK ] Started Load/Save Random Seed.[ OK ] Started Create Volatile Files and Directories.[ OK ] Started udev Kernel Device Manager. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown...[ OK ] Started Update UTMP about System Boot/Shutdown.[ OK ] Started Network Time Synchronization.[ OK ] Reached target System Initialization.[ OK ] Started Daily Cleanup of Temporary Directories.[ OK ] Reached target System Time Set.[ OK ] Reached target System Time Synchronized.[ OK ] Reached target Timers.[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.[ OK ] Listening on D-Bus System Message Bus Socket. Starting sshd.socket.[ OK ] Listening on sshd.socket.[ OK ] Reached target Sockets.[ OK ] Reached target Basic System.[ OK ] Started Kernel Logging Service.[ OK ] Started System Logging Service.[ OK ] Started D-Bus System Message Bus. Starting IPv6 Packet Filtering Framework... Starting IPv4 Packet Filtering Framework...[ 7.472913] ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 Starting Telephony service...[ OK ] Started optee services. Starting PowerVR consumer services... Starting rng-tools.service... Starting Login Service...[ 7.584191] Bluetooth: Core ver 2.22[ 7.587993] NET: Registered protocol family 31[ 7.606624] Bluetooth: HCI device and connection manager initialized[ 7.614825] Bluetooth: HCI socket layer initialized[ 7.624035] st-gyro-i2c 16-006b: supply vdd not found, using dummy regulator[ 7.632147] st-gyro-i2c 16-006b: supply vddio not found, using dummy regulator[ 7.639765] Bluetooth: L2CAP socket layer initialized[ 7.644959] Bluetooth: SCO socket layer initialized[ OK ] Started IPv6 Packet Filtering Framework.[ 7.666285] st-lsm9ds0-i2c 16-001d: supply vdd not found, using dummy regulator[ OK 7.681455] st-lsm9ds0-i2c 16-001d: supply vddio not found, using dummy regulatorm] Started IPv4 Packet Filtering Framework.[ 7.737403] Bluetooth: HCI UART driver ver 2.3[ 7.764987] Bluetooth: HCI UART protocol H4 registered[ 7.769397] iio iio:device0: registered gyroscope lsm9ds0_gyro[ 7.782119] Bluetooth: HCI UART protocol LL registered[ 7.783553] iio iio:device1: registered accelerometer lsm9ds0[ OK ] Started rng-tools.service.[ 7.832443] Bluetooth: HCI UART protocol Broadcom registered[ 7.839519] Bluetooth: HCI UART protocol QCA registered[ 7.897692] iio iio:device2: registered magnetometer lsm9ds0[ 7.911081] ccree e6601000.crypto: ARM ccree device initialized[ 7.945585] Bluetooth: hci0: change remote baud rate command in firmware[ OK ] Started Telephony service.[ OK ] Started Login Service.[ OK ] Created slice system-weston.slice.[ OK ] Reached target Network (Pre). Starting Save/Restore Sound Card State... Starting pvrinit.service... Starting Network Service...[ OK ] Started Save/Restore Sound Card State.[ OK ] Reached target Sound Card.[ OK ] Started Network Service. Starting Network Name Resolution...[ 8.415930] Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=180)[ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Load/Save RF Kill Switch Status...[ OK ] Started PowerVR consumer services. Starting Bluetooth service...[ OK ] Started Network Name Resolution.[ OK ] Started Load/Save RF Kill Switch Status.[ OK ] Reached target Network.[ OK ] Reached target Host and Network Name Lookups.[ 8.632763] cfg80211: Loading compiled-in X.509 certificates for regulatory database Starting Avahi mDNS/DNS-SD Stack...[ 8.651324] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'[ 8.664930] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2[ 8.673635] cfg80211: failed to load regulatory.db Starting Permit User Sessions... Starting Target Communication Framework agent...[ OK ] Started pvrinit.service.[ OK ] Started Permit User Sessions.[ OK ] Started Getty on tty1. Starting rc.mm.service...[ OK ] Started Serial Getty on ttySC0.[ OK ] Reached target Login Prompts.[ OK ] Started Bluetooth service.[ OK ] Started rc.mm.service.[ OK ] Reached target Bluetooth. Starting uim-sysfs.service...[ OK ] Started Avahi mDNS/DNS-SD Stack.[ 8.973325] Bluetooth: BNEP (Ethernet Emulation) ver 1.3[ 8.978752] Bluetooth: BNEP socket layer initialized[ 8.993234] (stk) : gpio 343 request failed[ 8.993279] kim: probe of kim failed with error -16 Starting Hostname Service...[ OK ] Started Target Communication Framework agent.[ 9.064221] wl18xx_driver wl18xx.6.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2[ 9.074996] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -2[ 9.085842] wlcore: WARNING falling back to default config[ OK ] Started Hostname Service.[ OK ] Started uim-sysfs.service. Starting pulseaudio.service...[ 9.580095] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)[ 9.589159] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.[ 9.598014] wlcore: WARNING This default nvs file can be removed from the file system[ 9.609465] wlcore: loaded[ OK ] Started pulseaudio.service.[ OK ] Reached target Multi-User System. Starting Update UTMP about System Runlevel Changes...[ OK ] Started Weston Wayland Compositor.[ OK ] Started Update UTMP about System Runlevel Changes.[ 10.773788] audit: type=1006 audit(1637682732.167:2): pid=701 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=1 res=1
Poky (Yocto Project Reference Distro) 3.1.4 h3ulcb ttySC0
The log look fine.How is the result of Yocto v5.5.0?
Do you have any updates?
Hi,
This question has been opened but there is no reply for a long time.We have a tentative answer already, so I will close this question.If you have any updates or want to ask another question, please post new question.