Boot failure on Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+

Hi,

 

I am trying to bring up Linux on Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+, but failed with kernel panic. I have followed the build instructions described in https://elinux.org/R-Car/Boards/Kingfisher#How_to_build For Yocto v3.19.0 (

Linux_Boot_Log.txt
[    0.000162] NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.21
[    0.005724] NOTICE:  BL2: PRR is R-Car H3 Ver.2.0
[    0.010388] NOTICE:  BL2: Board is Starter Kit Rev.---
[    0.015507] NOTICE:  BL2: Boot device is eMMC(50MHz x8)
[    0.020674] NOTICE:  BL2: LCM state is CM
[    0.024714] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x53
[    0.030704] NOTICE:  BL2: DDR1600(rev.0.33)NOTICE:  [COLD_BOOT]NOTICE:  ..0
[    0.077825] NOTICE:  BL2: DRAM Split is 4ch
[    0.081707] NOTICE:  BL2: QoS is default setting(rev.0.19)
[    0.087150] NOTICE:  BL2: DRAM refresh interval 1.95 usec
[    0.105768] NOTICE:  BL2: Lossy Decomp areas
[    0.108548] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.115633] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.122545] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.129459] NOTICE:  BL2: v1.4(release):15dba6b
[    0.133949] NOTICE:  BL2: Built : 12:11:08, Jul 29 2019
[    0.139137] NOTICE:  BL2: Normal boot
[    0.142778] NOTICE:  BL2: eMMC boot from partition 1
[    0.149671] NOTICE:  BL2: Load dst=0xe6323d00 src=(p:1)0x30000(384) len=0x200(1)
[    0.155803] NOTICE:  BL2: Load dst=0x43f00000 src=(p:1)0x30400(386) len=0x1800(12)
[    0.163450] NOTICE:  BL2: Load dst=0x44000000 src=(p:1)0x40000(512) len=0x10000(128)
[    0.172416] NOTICE:  BL2: Load dst=0x44100000 src=(p:1)0x200000(4096) len=0x100000(2048)
[    0.202346] NOTICE:  BL2: Load dst=0x50000000 src=(p:2)0x0(0) len=0x100000(2048)


U-Boot 2015.04 (Jul 29 2019 - 17:42:02)

CPU: Renesas Electronics R8A7795 rev 2.0
Board: H3ULCB
I2C:   ready
DRAM:  7.9 GiB
Bank #0: 0x048000000 - 0x0bfffffff, 1.9 GiB
Bank #1: 0x500000000 - 0x57fffffff, 2 GiB
Bank #2: 0x600000000 - 0x67fffffff, 2 GiB
Bank #3: 0x700000000 - 0x77fffffff, 2 GiB

MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   ravb
Hit any key to stop autoboot:  0
=> printenv
baudrate=115200
bootarg=ignore_loglevel root=/dev/mmcblk1p1 rw rootwait
bootargs=root=/dev/mmcblk1p1 rw rootwait
bootcmd=ext4load mmc 0:1 48080000 /boot/Image; ext4load mmc 0:1 48000000 /boot/r8a7795-h3ulcb-4x2g-kf.dtb; booti 48080000 - 48000000
bootdelay=3
ethact=ravb
ethaddr=2E:09:0A:03:92:7C
fdt_high=0xffffffffffffffff
filesize=fbba00
initrd_high=0xffffffffffffffff
ipaddr=169.254.214.130
serverip=169.254.214.138
stderr=serial
stdin=serial
stdout=serial
ver=U-Boot 2015.04 (Jul 29 2019 - 17:42:02)

Environment size: 537/131068 bytes
=> run bootcmd
15165952 bytes read in 2254 ms (6.4 MiB/s)
92825 bytes read in 45 ms (2 MiB/s)
## Flattened Device Tree blob at 48000000
   Booting using the fdt blob at 0x48000000
   Using Device Tree in place at 0000000048000000, end 0000000048019a98

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.75-ltsi-yocto-standard (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #2 SMP PREEMPT Tue Feb 4 05:39:28 UTC 2020
[    0.000000] Boot CPU: AArch64 Processor [411fd073]
[    0.000000] Machine model: Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma@57000000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,multimedia@70000000, compatible id shared-dma-pool
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000077fffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x77ff6af80-0x77ff6ca7f]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000048000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000077fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000048000000-0x0000000053ffffff]
[    0.000000]   node   0: [mem 0x0000000057000000-0x00000000bfffffff]
[    0.000000]   node   0: [mem 0x0000000500000000-0x000000057fffffff]
[    0.000000]   node   0: [mem 0x0000000600000000-0x000000067fffffff]
[    0.000000]   node   0: [mem 0x0000000700000000-0x000000077fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000077fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS resident on physical CPU 0x0
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 24 pages/cpu @ffff80073fea5000 s57624 r8192 d32488 u98304
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 2020032
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=/dev/mmcblk1p1 rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] software IO TLB [mem 0xbbfff000-0xbffff000] (64MB) mapped at [ffff80007bfff000-ffff80007fffefff]
[    0.000000] Memory: 7322880K/8208384K available (9596K kernel code, 666K rwdata, 3780K rodata, 704K init, 385K bss, 213760K reserved, 671744K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
[    0.000000]       .text : 0xffff000008080000 - 0xffff0000089e0000   (  9600 KB)
[    0.000000]     .rodata : 0xffff0000089e0000 - 0xffff000008da0000   (  3840 KB)
[    0.000000]       .init : 0xffff000008da0000 - 0xffff000008e50000   (   704 KB)
[    0.000000]       .data : 0xffff000008e50000 - 0xffff000008ef6a00   (   667 KB)
[    0.000000]        .bss : 0xffff000008ef6a00 - 0xffff000008f56fc8   (   386 KB)
[    0.000000]     fixed   : 0xffff7dfffe7f9000 - 0xffff7dfffec00000   (  4124 KB)
[    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
[    0.000000]               0xffff7e0000200000 - 0xffff7e001d000000   (   462 MB actual)
[    0.000000]     memory  : 0xffff800008000000 - 0xffff800740000000   ( 29568 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Adjusting CPU interface base to 0x00000000f102f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns
[    0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns
[    0.000131] Console: colour dummy device 80x25
[    0.000363] console [tty0] enabled
[    0.000413] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)
[    0.000426] pid_max: default: 32768 minimum: 301
[    0.000483] Security Framework initialized
[    0.003965] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.005715] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.005793] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.005855] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.019948] ASID allocator initialised with 32768 entries
[    0.027937] Hierarchical SRCU implementation.
[    0.036908] Detected Renesas R-Car Gen3 r8a7795 ES2.0
[    0.037600] EFI services will not be available.
[    0.043968] smp: Bringing up secondary CPUs ...
[    0.072161] Detected PIPT I-cache on CPU1
[    0.072206] CPU1: Booted secondary processor [411fd073]
[    0.100172] Detected PIPT I-cache on CPU2
[    0.100195] CPU2: Booted secondary processor [411fd073]
[    0.128205] Detected PIPT I-cache on CPU3
[    0.128225] CPU3: Booted secondary processor [411fd073]
[    0.156250] CPU features: enabling workaround for ARM erratum 845719
[    0.156258] Detected VIPT I-cache on CPU4
[    0.156296] CPU4: Booted secondary processor [410fd034]
[    0.184272] Detected VIPT I-cache on CPU5
[    0.184295] CPU5: Booted secondary processor [410fd034]
[    0.212307] Detected VIPT I-cache on CPU6
[    0.212329] CPU6: Booted secondary processor [410fd034]
[    0.240342] Detected VIPT I-cache on CPU7
[    0.240364] CPU7: Booted secondary processor [410fd034]
[    0.240435] smp: Brought up 1 node, 8 CPUs
[    0.240497] SMP: Total of 8 processors activated.
[    0.240505] CPU features: detected feature: 32-bit EL0 Support
[    0.240512] CPU features: detected feature: Kernel page table isolation (KPTI)
[    0.247513] CPU: All CPU(s) started at EL2
[    0.247539] alternatives: patching kernel code
[    0.248343] devtmpfs: initialized
[    0.254915] random: get_random_u32 called from bucket_table_alloc+0x108/0x260 with crng_init=0
[    0.255328] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.255403] futex hash table entries: 2048 (order: 6, 262144 bytes)
[    0.264856] pinctrl core: initialized pinctrl subsystem
[    0.266162] DMI not present or invalid.
[    0.266401] NET: Registered protocol family 16
[    0.267617] cpuidle: using governor menu
[    0.267719] vdso: 2 pages (1 code @ ffff0000089e6000, 1 data @ ffff000008e55000)
[    0.267737] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.268384] DMA: preallocated 256 KiB pool for atomic allocations
[    0.268470] Serial: AMBA PL011 UART driver
[    0.272031] sh-pfc e6060000.pin-controller: r8a77951_pfc support registered
[    0.295951] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.297063] ACPI: Interpreter disabled.
[    0.299342] rcar-avs: use avs value: 0
[    0.299490] rcar-avs: /cpus/cpu@0 is running with: /opp_table0
[    0.299502] rcar-avs: /cpus/cpu@1 is running with: /opp_table0
[    0.299514] rcar-avs: /cpus/cpu@2 is running with: /opp_table0
[    0.299526] rcar-avs: /cpus/cpu@3 is running with: /opp_table0
[    0.299552] rcar-avs: /soc/gsx@fd000000 is running with: /gsx_opp_table0
[    0.301286] ipmmu-vmsa e67b0000.mmu: IPMMU context 0 is reserved
[    0.301865] vgaarb: loaded
[    0.302063] SCSI subsystem initialized
[    0.302380] usbcore: registered new interface driver usbfs
[    0.302417] usbcore: registered new interface driver hub
[    0.302473] usbcore: registered new device driver usb
[    0.303364] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz
[    0.303690] media: Linux media interface: v0.10
[    0.303714] Linux video capture interface: v2.00
[    0.303787] pps_core: LinuxPPS API ver. 1 registered
[    0.303795] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.303813] PTP clock support registered
[    0.304110] EDAC MC: Ver: 3.0.0
[    0.304273] dmi: Firmware registration failed.
[    0.305248] clocksource: Switched to clocksource arch_sys_counter
[    0.305375] VFS: Disk quotas dquot_6.6.0
[    0.305415] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.305519] pnp: PnP ACPI: disabled
[    0.309542] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    0.309664] NET: Registered protocol family 2
[    0.310210] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[    0.310624] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.311273] TCP: Hash tables configured (established 65536 bind 65536)
[    0.311429] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    0.311556] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    0.311786] NET: Registered protocol family 1
[    0.313073] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.313667] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available
[    0.314196] kvm [1]: 8-bit VMID
[    0.314902] kvm [1]: vgic interrupt IRQ1
[    0.315028] kvm [1]: Hyp mode initialized successfully
[    0.317067] audit: initializing netlink subsys (disabled)
[    0.317161] audit: type=2000 audit(0.307:1): state=initialized audit_enabled=0 res=1
[    0.317501] workingset: timestamp_bits=44 max_order=21 bucket_order=0
[    0.320709] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.322629] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    0.322649] io scheduler noop registered
[    0.322656] io scheduler deadline registered
[    0.322752] io scheduler cfq registered (default)
[    0.322760] io scheduler mq-deadline registered
[    0.322767] io scheduler kyber registered
[    0.326710] gpio_rcar e6050000.gpio: driving 16 GPIOs
[    0.326952] gpio_rcar e6051000.gpio: driving 29 GPIOs
[    0.327095] GPIO line 455 (BL PWM 100%) hogged as output/high
[    0.327205] gpio_rcar e6052000.gpio: driving 15 GPIOs
[    0.327430] gpio_rcar e6053000.gpio: driving 16 GPIOs
[    0.327564] GPIO line 432 (MOST RST) hogged as output/high
[    0.327668] gpio_rcar e6054000.gpio: driving 18 GPIOs
[    0.327878] gpio_rcar e6055000.gpio: driving 26 GPIOs
[    0.328000] GPIO line 381 (Onboard MCh Audio) hogged as output/high
[    0.328112] gpio_rcar e6055400.gpio: driving 32 GPIOs
[    0.328327] gpio_rcar e6055800.gpio: driving 4 GPIOs
[    0.329389] rcar-pcie fe000000.pcie: no pcie3v3 regulator found
[    0.329407] rcar-pcie fe000000.pcie: no pcie1v8 regulator found
[    0.329417] OF: PCI: host bridge /soc/pcie@fe000000 ranges:
[    0.329440] OF: PCI:    IO 0xfe100000..0xfe1fffff -> 0x00000000
[    0.329454] OF: PCI:   MEM 0xfe200000..0xfe3fffff -> 0xfe200000
[    0.329465] OF: PCI:   MEM 0x30000000..0x37ffffff -> 0x30000000
[    0.329473] OF: PCI:   MEM 0x38000000..0x3fffffff -> 0x38000000
[    0.397170] rcar-pcie fe000000.pcie: PCIe link down
[    0.398875] EINJ: ACPI disabled.
[    0.415519] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.416929] SuperH (H)SCI(F) driver initialized
[    0.417530] e6540000.serial: ttySC1 at MMIO 0xe6540000 (irq = 35, base_baud = 0) is a hscif
[    0.418156] e6550000.serial: ttySC3 at MMIO 0xe6550000 (irq = 36, base_baud = 0) is a hscif
[    0.418713] e6e68000.serial: ttySC2 at MMIO 0xe6e68000 (irq = 122, base_baud = 0) is a scif
[    0.419183] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 123, base_baud = 0) is a scif
[    1.488269] console [ttySC0] enabled
[    1.493899] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.500525] [drm] No driver support for vblank timestamp query.
[    1.507132] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.517011] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.531217] loop: module loaded
[    1.537959] renesas-rpc ee200000.rpc0: using DMA read (dma0chan0)
[    1.544521] Bad mode in Error handler detected on CPU1, code 0xbf000000 -- SError
[    1.552007] Internal error: Oops - bad mode: 0 [#1] PREEMPT SMP
[    1.557923] Modules linked in:
[    1.560979] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.14.75-ltsi-yocto-standard #2
[    1.568719] Hardware name: Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+ (DT)
[    1.576720] task: ffff8007368a8000 task.stack: ffff000008068000
[    1.582646] PC is at rpc_wait+0x28/0x88
[    1.586477] LR is at rpc_wait+0x18/0x88
[    1.590309] pc : [<ffff0000085ff8a0>] lr : [<ffff0000085ff890>] pstate: 20000045
[    1.597699] sp : ffff00000806bbd0
[    1.601008] x29: ffff00000806bbd0 x28: ffff000008e37510
[    1.606318] x27: 0000000000000007 x26: ffff000008da046c
[    1.611627] x25: ffff000008efb000 x24: 0000000000000000
[    1.616936] x23: ffff8007364df400 x22: 0000000000000000
[    1.622245] x21: ffff800735a49410 x20: ffff8007364df798
[    1.627553] x19: ffff8007364df798 x18: 0000000000000000
[    1.632862] x17: 0000000000000020 x16: ffff000008a2a970
[    1.638170] x15: 0000000000000000 x14: 0000000000000400
[    1.643478] x13: 0000000000000400 x12: 0000000000000030
[    1.648786] x11: 0000000000000006 x10: 0101010101010101
[    1.654095] x9 : fffffffffffffffb x8 : 7f7f7f7f7f7f7f7f
[    1.659403] x7 : fefefeff646c606d x6 : 02000f00ec808080
[    1.664711] x5 : 0000000000000000 x4 : ffff000008f41218
[    1.670019] x3 : 0000000000000000 x2 : ffff000008e57000
[    1.675327] x1 : 0000000000000000 x0 : 00000000fffee16b
[    1.680637] Process swapper/0 (pid: 1, stack limit = 0xffff000008068000)
[    1.687333] Call trace:
[    1.689775] Exception stack(0xffff00000806ba90 to 0xffff00000806bbd0)
[    1.696211] ba80:                                   00000000fffee16b 0000000000000000
[    1.704037] baa0: ffff000008e57000 0000000000000000 ffff000008f41218 0000000000000000
[    1.711863] bac0: 02000f00ec808080 fefefeff646c606d 7f7f7f7f7f7f7f7f fffffffffffffffb
[    1.719689] bae0: 0101010101010101 0000000000000006 0000000000000030 0000000000000400
[    1.727515] bb00: 0000000000000400 0000000000000000 ffff000008a2a970 0000000000000020
[    1.735341] bb20: 0000000000000000 ffff8007364df798 ffff8007364df798 ffff800735a49410
[    1.743167] bb40: 0000000000000000 ffff8007364df400 0000000000000000 ffff000008efb000
[    1.750992] bb60: ffff000008da046c 0000000000000007 ffff000008e37510 ffff00000806bbd0
[    1.758818] bb80: ffff0000085ff890 ffff00000806bbd0 ffff0000085ff8a0 0000000020000045
[    1.766644] bba0: 0000000000000007 ffff0000084655b0 ffffffffffffffff ffff0000084655cc
[    1.774470] bbc0: ffff00000806bbd0 ffff0000085ff8a0
[    1.779343] [<ffff0000085ff8a0>] rpc_wait+0x28/0x88
[    1.784218] [<ffff000008600480>] rpc_hf_mode_ext+0x18/0xe8
[    1.789699] [<ffff000008600cfc>] rpc_hf_probe+0xcc/0x340
[    1.795010] [<ffff000008551fd0>] platform_drv_probe+0x58/0xb8
[    1.800755] [<ffff000008550238>] driver_probe_device+0x210/0x2d0
[    1.806758] [<ffff0000085503b4>] __driver_attach+0xbc/0xc0
[    1.812241] [<ffff00000854e394>] bus_for_each_dev+0x4c/0x98
[    1.817810] [<ffff00000854fb50>] driver_attach+0x20/0x28
[    1.823117] [<ffff00000854f6a0>] bus_add_driver+0x1b8/0x228
[    1.828686] [<ffff000008550d50>] driver_register+0x60/0xf8
[    1.834166] [<ffff000008551f20>] __platform_driver_register+0x40/0x48
[    1.840609] [<ffff000008dd5748>] rpc_hf_platform_driver_init+0x18/0x20
[    1.847136] [<ffff000008083c90>] do_one_initcall+0x38/0x128
[    1.852709] [<ffff000008da0d0c>] kernel_init_freeable+0x188/0x22c
[    1.858802] [<ffff0000089c3d50>] kernel_init+0x10/0x108
[    1.864023] [<ffff000008084ed8>] ret_from_fork+0x10/0x18
[    1.869332] Code: 900042c2 f9454041 8b000020 14000005 (f9454041)
[    1.875435] ---[ end trace 0a81961cb0a82ec8 ]---
[    1.880090] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[    1.880090]
[    1.889226] SMP: stopping secondary CPUs
[    1.893148] Kernel Offset: disabled
[    1.896633] CPU features: 0x1802004
[    1.900116] Memory Limit: none
[    1.903170] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[    1.903170]
Host PC: Ubuntu 18.04.1 LTS)

I have used  /boot/Image and /boot/r8a7795-h3ulcb-4x2g-kf.dtb for booting Linux.

The Bootlog messages  attached.

Kindly help me to resolve the issue or give some additional reference to get some details regarding the issue.

 

Thanks in advance,

Roopesh